LJDomestics

Forum Replies Created

Viewing 15 posts - 121 through 135 (of 610 total)
1 2 3 … 8 9 10 … 39 40 41
  • Author
    Posts
  • February 25, 2010 at 7:19 pm in reply to: dishwashers #313190
    LJDomestics
    Participant

    Re: dishwashers

    check it heats.
    check there is nothing obstructing the drain pump.
    check for blockage.

    February 25, 2010 at 9:58 am in reply to: Amica #313112
    LJDomestics
    Participant

    Re: Amica

    Thx Don.
    😉

    February 22, 2010 at 6:45 pm in reply to: Whirlpool ADG 450/3 aborting #312770
    LJDomestics
    Participant

    Re: Whirlpool ADG 450/3 aborting

    does it have a anti flood device fitted?

    February 22, 2010 at 3:35 pm in reply to: SIMPLE PCB REPAIR TIPS #309678
    LJDomestics
    Participant

    Re: SIMPLE PCB REPAIR TIPS

    Penguin45 wrote:

    just done a repair to exact same board as chris has posted here, FAULT = NO HEAT ( d3 ) locate and change the little resistor that says IN4007 24C

    February 18, 2010 at 2:35 pm in reply to: oxy’balls #311977
    LJDomestics
    Participant

    Re: oxy’balls

    😆 :rotl:

    February 16, 2010 at 8:21 pm in reply to: wheres the work gone? #311353
    LJDomestics
    Participant

    Re: wheres the work gone?

    Get ur asses over here and help me then.
    Just got in and about half way through stripping a hoover washer dryer down for bearing change…. warn out i could cry.

    seem to be getting busier and busier for some reason or other.

    but seriously…. thinking of turning some away if it dont slow a little.

    February 13, 2010 at 8:45 am in reply to: hoover hswd146 #311870
    LJDomestics
    Participant

    Re: hoover hswd146

    Thx again Chris.
    ur a star.
    Lee

    February 12, 2010 at 8:31 pm in reply to: hoover hswd146 #311868
    LJDomestics
    Participant

    Re: hoover hswd146

    cheers chris.

    dont have part numbers for me do ya matey?

    reccomend front plate seal aswell?

    thx.
    Lee

    February 12, 2010 at 7:31 am in reply to: Knee Pads #311555
    LJDomestics
    Participant

    Re: Knee Pads

    The missus bought me knee pads and the trousers to suit a couple of yrs ago, the trousers i wear… the pads are still in the bag. 😆

    February 10, 2010 at 8:08 pm in reply to: Hotpoint service manuals #311490
    LJDomestics
    Participant

    Re: Hotpoint service manuals

    iadom wrote:The Hotpoint/Indesit engineers dumped all of the hard copy manuals many years ago.

    I know of a certain forum member who acquired a pallet full of old manuals. 😉

    Jim.

    good mate of mine was also once a long term hotpoint engineer…when he retired he gave me all hes… your right jim…. about a pallet truck full.. burned a treat they did.
    😆

    February 10, 2010 at 8:06 pm in reply to: Hotpoint brushes removal tool #311603
    LJDomestics
    Participant

    Re: Hotpoint brushes removal tool

    terminal screwdriver.

    about 9 pence trade. lol

    February 8, 2010 at 8:28 pm in reply to: AWM8123 #311401
    LJDomestics
    Participant

    Re: AWM8123

    Cheers John.
    Your a star. 😉

    Lee.

    February 6, 2010 at 11:30 pm in reply to: Cheeky bar steward #310798
    LJDomestics
    Participant

    Re: Cheeky bar steward

    This trade customer service is paramount…..text is for the playground.

    February 5, 2010 at 6:48 pm in reply to: is this too expensive? #311076
    LJDomestics
    Participant

    Re: is this too expensive?

    u guaranteeing them too at those prices?

    might send the 7 half tonner down for the lot!

    February 1, 2010 at 7:56 pm in reply to: Just lost the job #310700
    LJDomestics
    Participant

    Re: Just lost the job

    £5 offered to fit it??

    tell her were to stick it and fit it herself.

  • Author
    Posts
Viewing 15 posts - 121 through 135 (of 610 total)
1 2 3 … 8 9 10 … 39 40 41