Forum Replies Created
-
Posts
-
Re: Hoover HNWF washer dryer f12
r600a wrote:http://prntscr.com/4lfnas
Bryan
That’s the error codes for the later Optima series using the 3 phase motor. This ones a Nextra model with a brush motor.Re: Replacement for Schreiber/ Huygens AMP 6314 larder fridg
Pretty standard size by the sound of if. You can always pull the fridge out then measure the space (HxWxD) to be sure of finding a suitable replacement.
Matching the existing outer door panels to a new F/F will be a little more of a challenge though.
Re: ISE Ci555 leaky
Has a neoprene rubber seal between the front and back tub halves. All comes out the front to access. Have fun! 😀
Re: zwf10020w e43
I would think the board is stuffed otherwise the pump would not fire up unless the door interlock allowed it to.
Re: Neff integrated dishwasher S5943X2GB/31problem
There no internal fuse for starters. The only certain way to be sure the PCB is cooked is to take it out and inspect it. 🙁
Re: Hotpoint FDW80 dishwasher playing dead
Yes of course. I’m suggesting that the display board is the problem.
Re: Neff integrated dishwasher S5943X2GB/31problem
You wouldn’t need to mess with the wires in order to change the door handle. That aside it very much sounds like you may have blown the control unit (aka PCB)?
These wires you refer to, were they going to the door microswitch from the on/off switch? And did one short to earth against the metal door?
Re: JTM struggling?
I think Bryan may have misunderstood what I said? Let me put it another way from what I have heard tell….
0800 have always supplied parts for 0800 chargeable jobs. They also have to provide JTM warranty work with their spares. If JTM is struggling, as I think they might be, having lost Argos work and their Sheffield outfit also rumoured to be closing maybe as a result. If JTM were to fold (only supposing) then engineers will still have to pay 0800 for the spares.
It’s just a rumour 😉
Re: Hotpoint FDW80 dishwasher playing dead
charliefixit wrote:Does this suggest the display module itself is OK?
I would think the opposite applies. The power module clearly recognises that the display module was disconnected so that would rule out the power module.
To quote Paddy McGuinness “….no likey? no lighty!” 😉
Re: bosch sgs45c02gb/11 dishwasher
That model is in fact the easiest to fix. Simple access underneath. Both the Impellor jug and PCB are cheap (the PCB rarely fails on these anyway) I’d say the heater the most likely suspect in this case.
This may go landfill but if you get chance to check out another then they are no problem. It’s the latest plastic base models that are BIG trouble, believe me! 🙁
Re: bosch sgs45c02gb/11 dishwasher
suedehead1 wrote:I hate dishwashers thanks for the reply.
But once you gain ‘the knowledge’ you will just love them and will be straining your leash to get at ’em. 😉
Re: service manuals
DDA wrote:Can anyone help me with the best way to source service manuals
Generally by being a service agent and having access the their web site to download .pdfs and such. Otherwise you have to ask nicely here on UKW for information AND possibly manuals( if you are lucky) specific to each make and model. Then store that priceless information on your hard drive for future reference.
Over the years I have stacked up quite a lot of guff using that method. (Though I don’t have any Samsung stuff, in case you ask).
The rule of thumb for starters is post a thread in Trade Tech asking for info for a specific make and model. Someone out here in the ether may spot your plea and help you out.
