[Muv]

Re: element thermostat readings :Beko Condenser Dryer DCU823

Hi I have the same
Machine here,assumedthe stat is a one shot, but after reading this. I’m not so sure now…only tested it for continuity…old habits etc…can you send me the same info please Neil?

Sent from my iPhone using Tapatalk

[Muv]

Re: Miele W3830 Paragon Plus

Check the metal part of the pump,if this is very hot to the touch,then this could be your problem…had a similar problem with one recently

Martin

Sent from my iPhone using Tapatalk

[Muv]

Re: hoover vhv680c vision 8kg vented dryer – all lights flas

Anyone have a service manual for this machine please?
Martin

[Muv]

Re: S/H Hotpoint WM inner drum.

I sometimes get them, but havent got any at moment…theres ine on ebay for £20 Item no
111712559309
Martin

[Muv]

Re: hoover vhv680c vision 8kg vented dryer – all lights flas

Hi martin, do you still have the manual for this dryer…got a customer who has tried replacing the board and heater himself…..need i say any more!!

[Muv]

Re: How to turn off end of cycle beep, Hotpoint BC20

Had a look for you in the manual,but nothing mentioned about it there!

Martin

Sent from my iPhone using Tapatalk

[Muv]

Re: miele w308 washing machine – Inlet flashing

Been having a rethink on this one today,now thinking the valves are not getting the full mains voltage,and are maybe not opening fully? Not sure what you mean when you say works fine when connected to another machine!
Martin

Sent from my iPhone using Tapatalk

[Muv]

Re: miele w308 washing machine – Inlet flashing

Hi Paul
I think from memory this is related to a blockage in the small grey pipe that runs down from the soap box, just heard the voicemail you left me,but am on my way to a funeral this morning so won’t have time to ring you…
But check all breather pipes first and see if that helps.
Martin

Sent from my iPhone using Tapatalk

[Muv]

Re: Whirlpool AWE 6517

Thanks Don

Sent from my iPhone using Tapatalk

[Muv]

Re: Whirlpool WAE 6517

All sorted now,it was indeed a faulty tacho coil!

Sent from my iPhone using Tapatalk

[Muv]

Re: Whirlpool WAE 6517

Sorry its a AWE 6517

[Muv]

Re: White Night CL43 – fixable or time for a change?

The motor start capacitor will,need changing to get the drum spinning as it should, as for the no heat fault this was caused because the heater has had no air to cool it down due to the motor fault, so if it has a reset button at the back, then that should push in to reset it…
Not certain about this model having a reset, so hopefully someone else can help,you further

Martin

[Muv]

Re: BOSCH WASHED MACHINE e 23

The E23 code means that a leak to the base of machine has been detected..
You need to check underneath the machine after removing the bottom cover..
There is a float device attached to this base so be careful when removing as the wires are notmthat long…
Youncan then pull off the commector and investigte where the leak is coming from….

But it could be just a case of water leaking in tomthe base if you have recently cleaned out the fluff filter.. Try putting some towels infront of the machine and tilting forward to let any remaining water run out of the front and on to the towels…
If it then happens againyou have a leak that needs sorting..

Hope this helps
Martin

[Muv]

Re: Beko WMA510W

Take a look underneath the machine. You may find the hose from the bottom of the tub,leading to the pump has come away whilst transporting the machine,also look at the rubber door seal as well,if these are ok,then look at the bottom area of the door seal after opening the door,make sure you pull out the folded areas and look there…

Martin

Sent from my iPhone using Tapatalk

[Muv]

Re: Bosch Classixx 6 1400 – Not spinning (F:21 error & 1min)

A small amount of clicking with new brushes is normal, until they bed themselves in, but it sounds as thought you may have not fitted them correctly maybe?
I would take the motor out and check that the whole surface of the brush is in contact with the armature, and not just the tip of them..
And also that the brushes when installed correctly are pushed in to the holder, ther mistny be any resistance, as this may cause the symtoms you describe, as in one brush may have just lost contact with the armature due to it not being free to move agains the spring pressure..
Is the machine showing any error codes or flashing lights?

Martin

[Author]

Posts