Forum Replies Created
-
Posts
-
Re: What have I done wrong – competition
silverbroom wrote:Would this be Lee Nelsons “Well good appliance repair” business?.
silverbroomErm no silverbroom sorry.
Eastlmark, your crate of virtual beer is virtually on its way
😉Re: What have I done wrong – competition
Well went back today turned the field coil around and Bob is indeed your aunties husband 😉
Thanks to all 🙂
Re: What have I done wrong – competition
I have found that every Bosch Exxcel I have had to change brushes on has needed the excess carbon cleaning away, or it has caused the spin to skip to end.
I don’t know why but I never have to do this on Bosch Classixx or the old Maxx machines 😕
I don”t normally have a problem with this job but I think today I was under pressure to be somewhere else at a given time and may have caused a lapse in concentration.
😳
Re: What have I done wrong – competition
As it has one of those horrible base plates, I had to take the front panel off. Also I tapped the brushes before selecting a spin. I am pretty sure that it was running ok before I removed the motor, the only thing I am not sure about is whether I put the field coil back on 180 degrees the wrong way.
I will return to the customer tomorrow and we shall see if I have to make good on my offer of virtual beer. 😉Re: What have I done wrong – competition
🙂 Thanks chaps, I know the brushes are the right way around, but the field coil maybe the wrong way around.
Thankyou.Your Crate of virtual beer is on its way 😆
Re: servicing bosch washer and dishwasher
Thanks for the advice chaps, it’s food for thought, I will bear that in mind when I speak to my customer before I offer any prices etc.
Cheers
😉
Re: servicing bosch washer and dishwasher
Cheers Martin, like I say an annual service does seem to be a thing of the past. I have had customers say that their old repairman would service their machines every year, and I have wondered what exactly they have done. Have they changed perfectly good parts? Generally if I am doing a repair I will give the machine a once over and if anything looks suspect, I’ll let the customer know and advise remedial action.
Thanks again.
Re: Beko WMA10W wont pick up into full spin
My partner (not that kind 😆 ) has been out to it and couldn’t find anything obvious, ie draining problems, carbons etc.
I’m thinking possibly timer fault.
Thanks for the replies though 😉
Re: Creda 48145 grill elements
Cheers Jim I think it’s the first one, out of stock at Connect 🙁
I’ll try my local supplier with that part number though.
Re: Servis M6713W washer
sometimes if your customer is a bit heavy handed, the outer door trim can slip over the inner trim causing the pecker to not quite reach the door lock usually a little pull on the outer trim will make it click back into position.
You will be able to see at a glance if this is the case as the door handle will not be sitting flush to the trim.
Re: electrolux ewf 14108w washing machine
I would check the Heater, I had the same fault a couple of weeks ago on a Zanussi, machine filled and started but then drained out and went to end cycle.
Re: Zanussi ZWS16270W / 914604003 Wont run a program
Checked carbons on mine and they were barely worn, so I don’t think carbon dust would be an issue with mine, but maybe on MadMacs’. :hmm:
Cheers though LMTGOWI
Re: Hoover AL130-01 Door seal melting
I would think it is most likely a fractured spider, I have had this myself a few times with the Hoover six range, where I haven’t been able to feel any give on the spider but when on a high spin with a load in, it will show its self up.
Re: Bosch Maxx WFL2260 – Poor quality wash
I have advised the customer that there is nothing wrong with their machine and to try different detergents ie tablets with a fixed dosage. I also warned that overloading the washer will cause it to not wash properly.
Thanks for your input everyone. 😀
