Forum Replies Created
-
Posts
-
Re: AEG OKO_Favorit 545i – 606384120
Thank you for your input to this dead thread Rosco.
Future readers please note that the appliance should be unplugged before any action is taken. The procedure described will drain a leak into the undertray by pouring the water onto the floor. The leak must then be traced and repaired.
Regards,
Penguin45.Re: AEG OKO 4040
Thank you for your input to this dead thread Rosco.
Future readers please note that the appliance should be unplugged before any action is taken. The procedure described will drain a leak into the undertray by pouring the water onto the floor. The leak must then be traced and repaired. It does not solve a “no drain” problem.
Regards,
Penguin45.Re: siphon mystery
Thank you for your input to this dead thread Rosco.
Future readers please note that the appliance should be unplugged before any action is taken. The procedure described will drain a leak into the undertray by pouring the water onto the floor. The leak must then be traced and repaired. It does not solve the syphoning problem.
Regards,
Penguin45.Re: Teka dishwasher error codes
Sounds like a Smeg code, Andy. E7? Flow detector not detected – not surprising really as it’s rarely fitted……… Try the Smeg reset, see if that’ll do it.
Regards,
Chris.Re: Hygena select oven not working
New timer. Dave Conway will be able to advise prices later.
Regards,
Penguin45.Re: F&P AW095AU – Dead!?
Check the pump and its circuitry. If out of circuit, the module will not power up. Also check inlet valves (64 ohms each).
Power off – there is power to the pump if the machine is plugged in.
Regards,
Penguin45.Re: Hygena select oven not working
You have almost certainly blown the switching mechanism for the oven contained in the timer unit.
Regards,
Penguin45.Re: Indesit DV 620 fails to empty & dreaded flashing lig
Timeout on drain. Your machine has a blockage, most likely an obstruction in the drain pump.
Power off if investigating further, or click the link below for an engineer.
Regards,
Penguin45.Re: F&P MW051-U Diag procedure and fault codes please.
To enter Diagnostics:
Power on at socket, off on machine. Press and hold “Wash Temp Down”, then “Power”. Yours is a phase 2 machine, so press “Advance” once. From there, use the spin buttons until “Hold” and “Slow spin” leds are lit. The pattern of lights on the wash progress board will now indicate any fault in binary code, from right to left.Regards,
Penguin45.Re: Indesit W103 programme selector clicks round and round
The “timer” will have broken internally and will need replacing. Please post full model number and serial number for your appliance – there are early and late timers fitted to this one model.
Duplicate post deleted.
Regards,
Penguin45.Re: Indesit WDG1295w
Fan motor problems Benji. It’s the only moving part not used in the wash cycle.
Power off if investigating further.
Regards,
Penguin45.Re: LG Washer dryers
What is it that you don’t like about the Bosch? A perfectly adequate machine with a 2 year guarantee. The Zanussi machines again are adequate, perhaps not as robust as the Bosch.
LG doesn’t tend to get mentioned much in these forums as it is relatively low volume. The brand is not particularly popular amongst the independent trade as LG does not have its own service network and this causes all sorts of issues. From your perspective, parts are expensive. If they haven’t got them, they’re a long way away and you’ll wait a long time.
Buy the Bosch – you know it make sense.
Regards,
Penguin45.Re: Which Brand of Washer/Dryer do I buy?
Check out the Seimens WXD1260, or go mad and buy a Meile WT2670WPS.
Regards,
Penguin45.Re: NEFF S4132 Heater problem
Email with part number to spares@ukwhitegoods.co.uk for ordering and prices.
Regards,
Penguin45.
