Seamy

Forum Replies Created

Viewing 15 posts - 1,636 through 1,650 (of 2,653 total)
1 2 3 … 109 110 111 … 175 176 177
  • Author
    Posts
  • January 28, 2011 at 7:34 pm in reply to: Beko Tumble Dryer DRCS68W #288931
    Seamy
    Participant

    Re: Beko Tumble Dryer DRCS68W

    I normally put an clamp meter on the live cable & monitor it, should take 7 amps (1400w) max on timed drying, then then go up to 9.6 amps (2000w) on sensor drying. If you go into service mode you can test it & see fault codes.

    January 28, 2011 at 2:56 pm in reply to: zanussi zkt641-h hob , help cannot unlock ! #342815
    Seamy
    Participant

    Re: zanussi zkt641-h hob , help cannot unlock !

    RTFM, its in the User Instructions, how to reset. Will check & post later if i can

    January 27, 2011 at 8:54 pm in reply to: Beko Tumble Dryer DRCS68W #288929
    Seamy
    Participant

    Re: Beko Tumble Dryer DRCS68W

    Theres an NTC at the front of the tub at the top with an earth connection attached to it, part num’ 2953460200. Try it on timed drying as sensor dry programs require damp clothing & if nothing is sensed it goes to finish.

    January 27, 2011 at 8:41 pm in reply to: configuring zanussi washing machines #342656
    Seamy
    Participant

    Re: configuring zanussi washing machines

    Previous ones, the chinese made ones are not computer literate as yet. :rolls:

    January 27, 2011 at 8:03 am in reply to: configuring zanussi washing machines #342654
    Seamy
    Participant

    Re: configuring zanussi washing machines

    Depends on which boards you refer to, older ones needed a code put in to it via the controls, new ones require a laptop & specific software called SideKick which is plugged into the board & configures it & also can be used to diagnose appliances.

    January 25, 2011 at 8:19 pm in reply to: Beko DWD 5410s not running programme and burning smell #342135
    Seamy
    Participant

    Re: Beko DWD 5410s not running programme and burning smell

    Repairable if you can get whatever is causing the jamming removed, if its seized the motor may need replacing.

    January 25, 2011 at 8:16 pm in reply to: Zanussi ZWF12070W taking 2 attempts to start #342525
    Seamy
    Participant

    Re: Zanussi ZWF12070W taking 2 attempts to start

    It might be a door switch problem or could be board fault or button issue, or cable to door interlock either.

    January 25, 2011 at 8:12 pm in reply to: Beko CA5410W fridge freezer #342538
    Seamy
    Participant

    Re: Beko CA5410W fridge freezer

    Not inexpensive, sounds like it needs a compressor changed & regassed.

    January 24, 2011 at 7:21 pm in reply to: Service/Repair Manual #342350
    Seamy
    Participant

    Re: Service/Repair Manual

    Only available to trade.

    Read rules on forum

    January 24, 2011 at 7:17 pm in reply to: Beko DWD 5410s not running programme and burning smell #342133
    Seamy
    Participant

    Re: Beko DWD 5410s not running programme and burning smell

    Sounds like the circulation pump motor is jammed or seized.

    January 24, 2011 at 7:15 pm in reply to: AEG T 59800 e32 #342338
    Seamy
    Participant

    Re: AEG T 59800 e32

    E32 = Conductimetric sensor signal frequency too low.
    Wiring faulty. Brushes worn/faulty. Electronic board faulty.

    January 24, 2011 at 6:38 pm in reply to: AEG T 59800 e32 #342337
    Seamy
    Participant

    Re: AEG T 59800 e32

    E32 = Conductimetric sensor signal frequency too low.
    Wiring faulty. Brushes worn/faulty. Electronic board faulty.

    January 22, 2011 at 10:58 am in reply to: refridgeration rig #342084
    Seamy
    Participant

    Re: refridgeration rig

    http://www.srw.co.uk/

    refrigeration equipment suppliers

    January 20, 2011 at 8:42 pm in reply to: AEG Favorit 40660 – Unable to fill #341906
    Seamy
    Participant

    Re: AEG Favorit 40660 – Unable to fill

    Sounds like it has not draining, or does not signal that it has drained, possible blockage of gunge in small thin tube to pressure switch.

    January 20, 2011 at 8:30 pm in reply to: Beko WME7247 #341917
    Seamy
    Participant

    Re: Beko WME7247

    Child lock on if its the prewash flashing & won’t start. Hold in the 2 child lock buttons for 3 secs or more to deactivate. If its another led flashing post it here & i’m sure someone will help.

  • Author
    Posts
Viewing 15 posts - 1,636 through 1,650 (of 2,653 total)
1 2 3 … 109 110 111 … 175 176 177