[Seamy]

Re: Miele washing machine dead

Board behind on off switch, check for bad connections, dry joints etc. Edge connections to boards have been troublesome.

[Seamy]

Re: Miele W820 Wash Motor

Motor pulley should come off as its listed as a spare part,

its part num’ 1689472
held on by countersunk screw 3494482
complete motor is 3555995

[Seamy]

Re: PTFE Oven liner?

Yeah its another class invention 😆 , if it moves & is sucked up over the fan oven vent it starves the fan of air & causes the element to blow. Another revenue generator like the dishwasher fresheners blocking the spray arms.
😉

[Seamy]

Re: Electrolux W355H

http://www.jla.com/

[Seamy]

Re: TDS Offline 2008

TDS online is the web version of TDS offline. You need an account & password to access it.
Allows you to see far more info on far more machines.
TDS online is out of date as soon as its published & some of the newer machines are not listed on it.

On Vista i’ve had problems getting TDS offline to work & Adobe reader 8.0 never opens properly with TDS for me either.
Bit of a pain.. 👿

[Seamy]

Re: Miele G7859 dishwasher F A fault

Are you sure its F A & not F 4 or F 9

Dishwasher faults codes i have are :–

F 00 No fault registered
F 01 NTC – temperature sensor or leads open-circuited
F 02 NTC – temperature sensor or leads short-circuited
F 03 Electronic unit fault
F 04 Heating fault: Heating circuit open-circuited
F 05 Drainage fault: Heating level switch
F 06 Water intake fault, too few pulses at start of step
F 07 Water intake fault, too few pulses at end of step
F 08 Water intake fault: Heating level switch has not activated
F 09 Heating level switch has reset after 62 min during steps ZT2 and ZT4

[Seamy]

Re: Beko dishwasher not heating

There is a service/diagnostics mode for this machine.
Its hard to understand because its a bad translation from Turkish.
My interpretation of it is:–

Switch off machine, select program 2, hold in start button & keep it held for 3 secs.
All indicators should come on for 2 secs’.
Release & press start button again.
Machine will run short diagnostic program, drain, fill, circulation, regen, detergent,heating to 65C, circulation again, pump out.
Press start button

faults will be shown by indicators:-
No indicators = no fault
Wash led = water inlet fault
End led = NTC fault
Both leds = Heater fault

if all indicators blink it also means no fault

[Seamy]

Re: Handles up or down?

And now the knives will cut through the bottom of the cutlery baskets & forks will go through & stop bottom spray arm from turning.

Another good revenue spinner thank you very much 😆

[Seamy]

Re: Beko dishwasher not heating

Have got report of same problem, going tomorow to check, let you know how i get on.

[Seamy]

Re: TDS Offline 2008

I found i had awful trouble with the ’07 version on Vista & with Adobe Reader.
Used TDS online but you don’t always have an internet connection while out on the road.

[Seamy]

Re: Ariston v Miele. Its a draw.

We have crazy Harvey’s shops in Ireland too. Go Harvey Go. 😆

[Seamy]

expertcat wrote:i use http://www.vistprint.co.uk

I upload my own graphics and they print them in belgium.

As a taster you can get 250 free and just pay the postage.

I have fridge magnets as well made up by them.

Think that should be http://www.vistaprint.co.uk

[Seamy]

Re: TDS disc

My TDS run on Vista Home Basic seems to have an issue with Adobe reader, is there a workaround?

Thanks in advance

[Seamy]

Re: MIELE W864 N/R 00/49670936

Miele

[Seamy]

Re: miele w844

Try this link, this Dutch guy offers a postal repair service on a lot of Miele boards….

http://members.home.nl/peter.stuart/miele/en/index.html

[Author]

Posts