Seamy

Forum Replies Created

Viewing 15 posts - 2,191 through 2,205 (of 2,653 total)
  • Author
    Posts
  • in reply to: ZT615 Zanussi D.W taking in very little water #235667
    Seamy
    Participant

    Re: ZT615 Zanussi D.W taking in very little water

    Are they in sump area, just below filter, or underneath machine?

    in reply to: Whirlpool Top Loader not spinning #234571
    Seamy
    Participant

    Re: Whirlpool Top Loader not spinning

    Motor is running, & pumping out.
    No agitation and no spinning.
    Is there a brake on them?

    in reply to: Whirlpool Top Loader not spinning #234568
    Seamy
    Participant

    Re: Whirlpool Top Loader not spinning

    Afraid its not the coupling.
    Must be a fault in the gear box or the transmission?

    in reply to: Commercial Dish/Glass Washers. #234917
    Seamy
    Participant

    Re: Commercial Dish/Glass Washers.

    Addititive pumps for bringing in rinse aid & detergent getting bunged up.
    Normal stuff like spray arms blocked, outlet pumps blocked with broken glass, broken wires at heater, etc.
    Most are drain only but some are pumped to empty.
    Did modifications on a few to allow start immediately rather than wait for heat-up which can leave machines slow in busy times.
    All cables are clearly marked in loom & you just have to join 2 connections together, this info is in service sheet which comes with each machine.

    in reply to: Commercial Dish/Glass Washers. #234915
    Seamy
    Participant

    Re: Commercial Dish/Glass Washers.

    I do a few Classeq glasswashers, they retail around £1k so are worth doing repairs on.

    in reply to: Whirlpool Top Loader not spinning #234562
    Seamy
    Participant

    Re: Whirlpool Top Loader not spinning

    Thanks mate, is that difficult to repair & how to go about it?

    in reply to: Ice maker #234209
    Seamy
    Participant

    Re: Ice maker

    What is the brand & model number of the ice maker?
    Ignis?

    in reply to: Miele s560 / s570 #234230
    Seamy
    Participant

    Re: Miele s560 / s570

    PCB may have dry joint. If theres a thermal cut-out mounted on PCB theres usually a bad connection at the solder joints.

    in reply to: Miele G646SC Dishwasher #233710
    Seamy
    Participant

    Re: Miele G646SC Dishwasher

    Inlet fault could be
    Kinked hose.
    Dirty filter.
    Waterproof system..
    Establish if its a outlet fault by looking for water still in dishwasher.
    Possible cause summit stuck in pump,
    solution:- remove said object by opening filter in sump & taking off non-return valve, check for obstruction of outlet pump impellor.
    💡
    Careful of shards of broken glass..

    in reply to: Who Makes Matsui Dishwasher #233599
    Seamy
    Participant

    Re: Who Makes Matsui Dishwasher

    OK :rolls:

    So it begins with C
    & it begins with H
    & are made by Midea formally known as May Dick
    I suggest rebranding to save cunfusion.
    Perhaps using the letters C – R – A – & P

    :conf:

    in reply to: $10 Callout Fee – service 24/7 #233348
    Seamy
    Participant

    Re: $10 Callout Fee – service 24/7

    is that website cozy con ?

    in reply to: Whirlpool ADG6340AV hose #233288
    Seamy
    Participant

    Re: Whirlpool ADG6340AV hose

    Bit like that only pipe comes out at top.
    Theres one other outlet onto which a ribbed (concertina type) hose is fixed with a clip i thought.
    Doesn’t look like that motor type though.

    in reply to: Whirlpool ADG6340AV hose #233286
    Seamy
    Participant

    Re: Whirlpool ADG6340AV hose

    Don’t think it was moulded on, this is a ribbed hose & was held on with a clip from memory.
    On circulation motor, water enters via heater & is expelled out top spout of wash-pump.
    The hose i need connects to this top outlet from circulation motor & seems to have been nibbled by a mouse as it is spraying water out in several places.

    in reply to: AEG 72630w wm not filling #233139
    Seamy
    Participant

    Re: AEG 72630w wm not filling

    Has it the motorized water distributer on top of soap dispenser.
    If it isn’t parked in proper position it won’t fill.

    in reply to: miele w/m #233040
    Seamy
    Participant

    Re: miele w/m

    Yes.. tell us the model & the fault shown please.

Viewing 15 posts - 2,191 through 2,205 (of 2,653 total)