[Seamy]

Re: Miele WT945 dryer overload fault

Theres a load sensor on the little shock-like leg which measures weight, check its moving up & down o.k & cabling to it.
Dryer load should normally only be about 3kgs as far as I can remember, normally 1/2 a wash load.
Think the load sensor can be calibrated in settings, it actually tells you how to do this in user manual.

[Seamy]

Re: Miele WT945 dryer stays on

You sure its not just anti crease running?

[Seamy]

Re: Lamona / Beko dishwasher faulty

Not sure, i’d try changing the valve & flowmeter that should count 4 litres of water to fill in, sounds like its not reading right.
Check cabling to it & to valve.

[Seamy]

Re: Having trouble with my Tricity Bendix AW1200W

I’d reckon its a pump thats needed, it won’t fill till it empties.

[Seamy]

Re: Zanussi Tumble Dryer

Some have a switch on the condenser, theres plastic keys that lock condenser in place, normally one of these makes a switch which needs to be made for appliance to run.
Other thing to look for is float switch sticking r pump not running either, its difficult not knowing model but in general any time a condenser stops (for any reason) it throws up “clean filter” empty water” as a reminder to user.

[Seamy]

Re: Beko Frost Free CDA539FS-2 (fridge section freezing food

Low on gas, not getting cold enough to knock off thermostat, so appliance runs continuously hence the over cold fridge.

[Seamy]

Re: AEG Favorit 911936627/04 not heating but element is fine

PCB more than likely has a faulty heater relay, part number for the board is 973911936627042

[Seamy]

Re: Meile Novotronic W980 fault codes

Would think it could be motor related, brushes worn perhaps.

[Seamy]

Re: Flavell FL95CRX.

I’d be changing the fan and element, if its the Beko type fan impelor in it change it to a Belling type. They are slow to reach full temp’, double check the door seal is good & door is closing tight, terminal block connections are tight etc. You could in theory put in a higher wattage element but bear in mind tha appliance was manufactured to a specification, so the selector switch contacts, thermostat contacts may buckle under extra load.

[Seamy]

Re: Stoves S7-C900HY hob E5 fault.

Controller data is faulty
IHE Electronics are defective
Replace the IHE

[Seamy]

Re: BEKO DCU8230 Sticks in program

Elaborate on what you mean by “sticking in its program”?
Does it stop heating & turn only once every few minutes for another 2 hours with end/anti crease led flashing or lit?
This is how appliance should function and is not a fault.
Its normally not faulty unless 2 l.e.ds flash together, if that happens please post which flash.

[Seamy]

Re: Beko Washing machine tripping electric

please tell me thats not true

[Seamy]

Re: zanussi fridge freezer zx97/5

Wiring diagrams can’t be supplied to the general public, see forum rules.
Would advise that the problem you describe of freezer working but fridge not sounds like the evaporator battery in freezer is blocked up with frost & no cold air can be circulated up to fridge by the fan in freezer section.
Advise you to totally defrost the appliance for 24-48 hours & try to run it again.
If it cools in fridge after this defrosting, i’d be looking at the defrosting being the problem.

[Seamy]

Re: Stoves range induction fault.

Very little on that one, it doesn’nt have fault codes I think, have access a wiring diagram if its any good to you.

[Seamy]

Re: Beko WM6167

Depends on the mileage of course, check armature when replacing brushes in case its rough.

[Author]

Posts