Simon46

Forum Replies Created

Viewing 15 posts - 226 through 240 (of 2,216 total)
  • Author
    Posts
  • in reply to: AEG Oven fault (BE3002001) – power cuts out #418097
    Simon46
    Participant

    Re: AEG Oven fault (BE3002001) – power cuts out

    Do you mean it trips the rcd on the consumer unit?

    in reply to: Smeg DF612SDX7 on off push button #417814
    Simon46
    Participant

    Re: Smeg DF612SDX7 on off push button

    Many thanks
    Simon

    in reply to: candy grando gc1472 d1 #417431
    Simon46
    Participant

    Re: candy grando gc1472 d1

    I had one this week that the v shaped heater bracket has actually cut through the element from the element moving up and down against it!
    S.

    in reply to: Bosch Washing Machine Question #416460
    Simon46
    Participant

    Re: Bosch Washing Machine Question

    Usually people leaning against machine whilst talking to each other in kitchen i find.

    in reply to: Siemans slimline lady dishwasher no fill #415778
    Simon46
    Participant

    Re: Siemans slimline lady dishwasher no fill

    Managed to decipher worn label SR73230GB/13 FD7304 the one with the salt fill 1/2 way up on the lhs cabinet . Been back again to reset antiflood diaphraghm in valve AGAIN. Filling ok so started wash and sat through whole wash cycle. Watched the foam in matrix build till it was flowing out of matrix and filling the pressure hoses which tripped valve again. Asked about rinse aid never used it and I confirmed tank empty. Drain hose so high under sink no chance of backfilling. Kids asked if they had put washing up liquid in dishwasher.
    Actually went out and bought customer Finish powerball tablets and sure enough no foam.
    Sat through whole wash again all ok. 3hrs in total spent.
    Took some of their tablets to try in my newer bosch dishwasher. At the moment it isn’t spraying water its just foam. opened door and its high.
    Tablets? Fairy lemon.
    S.

    in reply to: Indesit IDF125 door latch faulty and a leak! #415929
    Simon46
    Participant

    Re: Indesit IDF125 door latch faulty and a leak!

    Replace the door lock.
    S.

    in reply to: hotpoint 9526 with red spot toc on cabinet #415765
    Simon46
    Participant

    Re: hotpoint 9526 with red spot toc on cabinet

    :rotfl: At least he didnt cable tie his pecker!

    in reply to: hotpoint 9526 with red spot toc on cabinet #415762
    Simon46
    Participant

    Re: hotpoint 9526 with red spot toc on cabinet

    Sorry Yes lock microswitch wiring disconnected bypassed with red spot tumble dryer toc and sellotaped it to cabinet near right hand shock.
    S.

    in reply to: Siemens Wxl132gb/07 spin fault #415658
    Simon46
    Participant

    Re: Siemens Wxl132gb/07 spin fault

    How is it with no load?
    S.

    in reply to: AEG 6100 digitronic dispenser to tub hose #415354
    Simon46
    Participant

    Re: AEG 6100 digitronic dispenser to tub hose

    Excellent. Many thanks Don.

    S.

    in reply to: ariston advantage 2000 #415218
    Simon46
    Participant

    Re: ariston advantage 2000

    Motor brushes?

    in reply to: Hotpoint FFFL2000 sensor. where does it go? #414971
    Simon46
    Participant

    Re: Hotpoint FFFL2000 sensor. where does it go?

    I clipped it onto the top rear pipe of evaporator centrally. Is this correct position? It was in the iceblock.

    in reply to: Bosch condenser WTE84307 GB/13 #414874
    Simon46
    Participant

    Re: Bosch condenser WTE84307 GB/13

    Went to a wte84102 yesterday with same fault. Mine was pcb.

    in reply to: Dplomat APM8703/2 will not go into dry cycle #414868
    Simon46
    Participant

    Re: Dplomat APM8703/2 will not go into dry cycle

    Push half load button in.
    S.

    in reply to: Bosch WFO2260 Spin Cycle #413944
    Simon46
    Participant

    Re: Bosch WFO2260 Spin Cycle

    Old Brushes were not worn out and armature was clean. I was replacing them on my mums machine. Bad cut angle on brush batch.

Viewing 15 posts - 226 through 240 (of 2,216 total)