Simon46

Forum Replies Created

Viewing 15 posts - 1,246 through 1,260 (of 2,216 total)
1 2 3 … 83 84 85 … 146 147 148
  • Author
    Posts
  • May 6, 2007 at 5:57 pm in reply to: Siemens Oven isn’t heating #212682
    Simon46
    Participant

    Re: Siemens Oven isn’t heating

    Well Done. 😀

    S.

    May 6, 2007 at 5:46 am in reply to: AEG D4100 not heating #212812
    Simon46
    Participant

    Re: AEG D4100 not heating

    Were resistances checked with wires off? Elements usually work or not. Power may not be getting to them from switchgear. Remove power completely before diagnosis. Please do not test live. Or Repairs@ for an engineer.

    Regards
    Simon

    May 4, 2007 at 7:09 pm in reply to: Indesit WN1062WR Spider hub assy #212698
    Simon46
    Participant

    Re: Indesit WN1062WR Spider hub assy

    Thanks DE but my supplier has had one in stock for 4 yrs. Did it at cost. 😀 .

    Cant believe the bearings on this 94 machine. Grease is still golden and bronze is not grooved. 😯

    S.

    May 4, 2007 at 4:47 pm in reply to: bosch logixx 1400 fills/drains but not washes WFR2866GB #212703
    Simon46
    Participant

    Re: bosch logixx 1400 fills/drains but not washes WFR2866GB

    If filter has been emptied then drum should be empty. If Spin only selected does the drum turn?

    Regards
    Simon (wfr owner 😆 )

    May 4, 2007 at 12:29 pm in reply to: Indesit WN1062WR Spider hub assy #212696
    Simon46
    Participant

    Re: Indesit WN1062WR Spider hub assy

    Stainless.Went through the UNT range in shop.No luck. Has to be Genuine 037029. 100 quid plus vat 😥

    Thanks Andy
    S.

    May 4, 2007 at 5:58 am in reply to: Ignis ADL347 Dishwasher 11 flashes #212650
    Simon46
    Participant

    Re: Ignis ADL347 Dishwasher 11 flashes

    I have checked the switch changing state as it fills(physically and electrically both in and out of the dishwasher). expected that it was that but no.I have not had one like this before.

    Regards
    Simon

    May 3, 2007 at 4:29 pm in reply to: WMA – can’t get belt on? #212623
    Simon46
    Participant

    Re: WMA – can’t get belt on?

    Cable tie and cut arms 🙂 . Long sleeves a must.

    S.

    May 2, 2007 at 11:27 pm in reply to: Fiber Glass Matting Repairs to Plastic Outer Tubs? #212357
    Simon46
    Participant

    Re: Fiber Glass Matting Repairs to Plastic Outer Tubs?

    Used Kwiksteel today on Hoover with 3 scewdriver bits, roof nails coins etc. Above line. Will it hold?

    S.

    May 2, 2007 at 11:20 pm in reply to: BT Modem lock removal #212170
    Simon46
    Participant

    Re: BT Modem lock removal

    Wouldnt work MSCONFIG. Managed to load windows again on e drive to recover documents off C. Copied To CDROM. Partitioned C Drive to delete E. Then Formatted C and loaded XP version one off old PC. 16 Hours to get it all back with updates drivers etc. 😈

    :beer: :beer: :beer:
    Celebration.
    Try life without tinternet. Its so Hard.

    Many thanks
    S.

    May 2, 2007 at 8:26 am in reply to: BT Modem lock removal #212168
    Simon46
    Participant

    Re: BT Modem lock removal

    Thanks Jim. Unfortunately when PC put into safe mode would not come out of it. looks like windows is going to have to be installed again. Can i find the disc? no.
    Regards
    Simon

    April 30, 2007 at 8:15 am in reply to: Electra AWM 1100B Eco – Drum not turning and horrible Noise #212163
    Simon46
    Participant

    Re: Electra AWM 1100B Eco – Drum not turning and horrible No

    Capacitor first!

    Regards
    S.

    April 30, 2007 at 7:34 am in reply to: Bosch SPS51225/07 over filling #146415
    Simon46
    Participant

    Re: Bosch SPS51225/07 over filling

    Ta tony. Will treat it to some salt as well.

    Regards
    S.

    April 29, 2007 at 9:56 pm in reply to: Electra AWM 1100B Eco – Drum not turning and horrible Noise #212161
    Simon46
    Participant

    Re: Electra AWM 1100B Eco – Drum not turning and horrible No

    Also power off before going in. :zap:

    regards
    Simon

    April 29, 2007 at 9:54 pm in reply to: Bosch SPS51225/07 over filling #146413
    Simon46
    Participant

    Re: Bosch SPS51225/07 over filling

    Appliance is now filling but very slow transfer from tank to sump. Pump hunts have to add water from kettle.shoved pressure hose up sump no gunk. Any ideas?

    Regards
    S.

    April 28, 2007 at 1:28 pm in reply to: Cannon Oven gets hotter and hotter #212111
    Simon46
    Participant

    Re: Cannon Oven gets hotter and hotter

    Sounds thermostat related. Have you a model number?

    Regards
    Simon

  • Author
    Posts
Viewing 15 posts - 1,246 through 1,260 (of 2,216 total)
1 2 3 … 83 84 85 … 146 147 148