smartin

Forum Replies Created

Viewing 15 posts - 316 through 330 (of 536 total)
1 2 3 … 21 22 23 … 34 35 36
  • Author
    Posts
  • October 23, 2008 at 6:27 pm in reply to: hinari lifestyle hdw40 #266347
    smartin
    Participant

    Re: hinari lifestyle hdw40

    or you could just not turn it on 😆

    October 23, 2008 at 5:48 pm in reply to: resistor values #266348
    smartin
    Participant

    Re: resistor values

    follow this link simon and it clculates values for you
    http://www.dannyg.com/examples/res2/resistor.htm

    October 22, 2008 at 9:26 pm in reply to: daewoo FRS-2031IAL #266099
    smartin
    Participant

    Re: daewoo FRS-2031IAL

    you havnt mentioned why you changed the original pcb that may help

    October 22, 2008 at 9:21 pm in reply to: Hotpoint WF320P Module? #265976
    smartin
    Participant

    Re: Hotpoint WF320P Module?

    ive had a few where the start microswitch on the user pcb has come off causing exactly your problem.

    October 21, 2008 at 8:57 pm in reply to: Electrolux washer dryer overfill. #265984
    smartin
    Participant

    Re: Electrolux washer dryer overfill.

    you have probably pulled off or split one of the two pressure hoses that run up the side of the drum or cabinet next to the condensor worth a check.

    October 21, 2008 at 8:50 pm in reply to: CDA CW496 whirlpool #265941
    smartin
    Participant

    Re: CDA CW496 whirlpool

    machine could be siphoning as well.

    October 21, 2008 at 8:49 pm in reply to: wma1614 – not starting cycles #265954
    smartin
    Participant

    Re: wma1614 – not starting cycles

    valve ?

    October 20, 2008 at 6:38 pm in reply to: Neff half turn elements #264815
    smartin
    Participant

    Re: Neff half turn elements

    thats interesting because connect were selling these elements as genuine last year packed in plastic bags with a piece of paper inside with genuine part number printed on it, and im pretty damn sure that they come acked in brown paper.

    October 17, 2008 at 9:33 pm in reply to: BOSCH WVT13240GB/01 E14 FAULT #265697
    smartin
    Participant

    Re: BOSCH WVT13240GB/01 E14 FAULT

    the known error codes section at the top of the page is a great place to start looking as a clue to the fault then all will be revealed, is a common problem on these

    October 14, 2008 at 9:21 pm in reply to: Hotpoint FF187 #265152
    smartin
    Participant

    Re: Hotpoint FF187

    also make sure they are using the super freeze when putting fresh food in

    October 9, 2008 at 10:13 pm in reply to: Ariston A1636 #264759
    smartin
    Participant

    Re: Ariston A1636

    check heater and ntc if you already havnt plus wiring to ntc.

    October 9, 2008 at 10:10 pm in reply to: Whirlpool shame #264724
    smartin
    Participant

    Re: Whirlpool shame:evil:

    haha went to an undercounter fridge yesterday (whirlpool) 😆 made in p.r.c also a while back went to a hoover slimline dw again made in p.r.c.

    October 7, 2008 at 10:36 pm in reply to: PRETEIGE PR225FFZS FREEZER #264503
    smartin
    Participant

    Re: PRETEIGE PR225FFZS FREEZER

    also there is a mod for evap sensor move it from bottom and fix to top of evaporator

    October 6, 2008 at 8:01 pm in reply to: Bosch oven HBN730550B burning base of food #264439
    smartin
    Participant

    Re: Bosch oven HBN730550B burning base of food

    yes it has 3 oven elements, 1 is used for fan assisted cooking (a circle with a fan in the middle and 2 elements on coventional heating ( 2 horizontal lines) if you normally cook on contentional then an elemnt failure would cause this problem as would a faulty door seal hope this helps

    October 6, 2008 at 6:53 pm in reply to: Whirlpool AWZ3413 #264422
    smartin
    Participant

    Re: Whirlpool AWZ3413

    forgive my bluntness but how do you know its broken if you dont know where it is and havn,t seen it ❓

  • Author
    Posts
Viewing 15 posts - 316 through 330 (of 536 total)
1 2 3 … 21 22 23 … 34 35 36