Forum Replies Created
-
Posts
-
Re: Neff Hinge replacement U1661
It may have the triple glazed door, without the full E-Nr can’t say for sure.
If it has then the inner glass panel will pull away if you grab it at the bottom edge and lift.
Check the instruction book it will have a section on removing and cleaning the door.
Re: Bosch HBN6450GB/02 Oven bottom element connections/volts
The outer part of the element should have a feed to it of 230-250V, the inner should be fed with 90v.
This is a complicated appliance, if you are sure that you have connected the element up correctly then I would consider calling somebody out.
Please do not carry out any further live testing, power off before removing any panels :zap:
Re: Bosch WTA 3500 Tumble Dryer Door Catch
Use a small blade terminal driver to prise the door skin apart.
You will also need a small torx bit to remove the fixing screws for the hook IIRC it’s a T-15.
Re: siemens SE25M276GB, dishwasher tabs/rinse aid
Bin the 3in1 type tablets altogether and use seperate, good quality powder, rinse aid and salt.
The 3in1 things just don’t do what they say on the tin I’m affraid, you’ll get a much better wash result using seperates 8)
HTH
Re: bosch dishwasher
Still no E-NR, it would help massively you know :rolls:
The mushroom is the overfill safety s/w. It needs to be snapped on it’s stem to remove it. So you’ll need a new one if you do remove it, that’s why we need the E-Nr see 😉
The “timer” on the heater is a clockwork diverter valve for top and bottom spray arms.
I can only assume the grey box you refer to is the aquastop ❓
The “little round box” as you call it again without E-Nr I can only guess it’s the impellor jug (flow meter) replaces the old pressure chamber.
Re: bosch dishwasher
No it certainly aint the right E-Nr.
It should be something like SGV????GB/??
As for why it wont fill, can’t really say until you give us an E-Nr.
Re: Bosch D/W SGS43E08GB (S9G1B) strip down
WHOA there tiger.
There is absolutely no need to completely strip the tank to remove or refit the circ pump.
Once door skin, bottom steel plate and side panels are off simply remove the front and rear securing screws holding the tank to the base, and the hinge cord on the RHS.
Raise RHS away from base insert a screwdriver (or similar wedge) under leg holding hinge plate and on top of plastic base. Bobs yer uncle, loads of room job done in thirty mins or so 😉
Re: neff oven
On one side you should have 4 wires and only a single connection on the other.
The 4 connections should go to
1. TOC
2.Top element
3.Bottom element
4.Grill element
The single on the other side goes to the selector s/w position 7a
Unfortunately I don’t have the colours for the wires, but I can’t ever remember a green and white connection, you sure it’s not green and yellow 😆
Re: bosch programme duration has increased
Omar wrote:
The dishwasher still cleans and dries as it should.Then there is no problem with the m/c.
As Penguin and Greg rightly stated the internal sensors are altering the programme times so that you get the best wash result.
Re: Recommended Listening
http://www.youtube.com/watch?v=uezNXwlSCTc
Josh Homme, Dave Grohl and Jack Black.
Class
Re: Neff Dish Washer Taking Out Kitchen R.C.D
The only way you’ll find it is to chase it with a megger, it really could be anything :rolls:
I’d start with the suppressor and work inwards.
Re: Leaky Bosch Toploader
[quote= They show 216489 as ‘complete‘ so I wonder if that includes 165989,165990,165991 & 299295? 😕
Yup 216489 comes with all the other bits and bobs.
Can’t say I’ve ever seen that fault before though 😕
Re: Leaky Bosch Toploader
I’ve had a few where they leak from the O rings where the matrix connects to the dispenser.
It’s been a while since I changed one though. IIRC it’s one of those jobs that look worse than it actually is.
If you peel the seal back under the lid there are maybe six screws to remove probably a couple at the back and a couple at the front through the fascia. Once all the screws are out you can lift the top away.
Sorry I can’t remember the exact procedure but I know I was pleasntly surprised at how easy it was after the first one I did:wink:
I would go with the matrix and dispenser BTW.
Anyway Greg will likely be along soon and give you a blow by blow account 😀
