Forum Replies Created
-
AuthorPosts
-
March 5, 2008 at 8:57 pm in reply to: NEFF dishwasher not draining – followed suggestions on forum #245016
superfix
ParticipantRe: NEFF dishwasher not draining – followed suggestions on f
That makes three 😕
superfix
ParticipantRe: Bosch dishwasher heater
You sure it’s not an SGS5302gb/08. As there seems to be too many zeros in the E-Nr 😉
superfix
ParticipantRe: bosch kgu3201gb/01 fault code
NTC is foamed into rear wall, unreplaceable.
Only fix is a new pcb that bypasses said NTC.
superfix
ParticipantRe: Bosch WAE 28467 won’t spin some items
You’ve answered your own question there.
The m/c has detected unbalanced load, you need an even distribution of the load across the drum, otherwise you’ve no chance of it spinning.
Underloading will cause the same problems as overloading. You need to be careful though with bath mats etc as they become very heavy when wet and cause premature bearing/drum failure.
superfix
ParticipantRe: Bosch Dishwasher SGS43A18/GB27
I’d double check your coding sheet.
No way should it have 71 mins on quickwash, normally somewhere around 30-40 mins.
On quickwash once it has finished filling it should give a feed to both heater and dispenser ptc virtually as soon as the valve shuts off.
superfix
ParticipantRe: Bosch fridge/freezer
Don’t think the ntc is the problem on this one I’m affraid.
The symptoms for that fault are that it reaches temp and the ntc cuts the motor off then it won’t restart unless the appliance is turned off then on again.
I agree with Greg it sounds like a system fault.
superfix
ParticipantRe: NEFF COOKER HOOD D8150N0/01
Could be filters need cleaning.
After x amount of hours some display a clean filter function.
See the manual for resetting.
superfix
ParticipantRe: Bosch Washer Dryer WVF2402GB/02, FD8406
Linda wrote:No, carer definitely not overloading machine. There was only one little sheet in it at the time anyway.
Underloading can be as bad as overloading, causes excess vibration and loosens things up.
superfix
ParticipantRe: Siemens WT6608VGB/02 T/Dryer fault
If there is a “select” button try that one first. Turn m/c on and hold the button in (normally about 5 seconds).
Failing that try ’em all til you find the right one.
superfix
ParticipantRe: Bosch Washer Dryer WVF2402GB/02, FD8406
Definately no known fault with this.
I have only ever had one do it and that was due to overloading :rolls:
Perhaps the carer is over/under loading the m/c. :con:
January 28, 2008 at 1:04 pm in reply to: NEFF – U1721N0GB/02 MIDDLE SECTION OF UPPER GRILL ELEMENT NO #241364superfix
ParticipantRe: NEFF – U1721N0GB/02 MIDDLE SECTION OF UPPER GRILL ELEMEN
Are you sure it’s set to the grill setting? and not to conventional top/bottom heat.
Cos on top/bottom heat it will only use the outer part of the element.
superfix
ParticipantRe: Siemens WT6608VGB/02 T/Dryer fault
Ask for the instruction book.
My guess is childlock has been set 😉
Normally a case of holding down one of the buttons for about 4 seconds to set/deselect.
superfix
ParticipantRe: Light inside siemans fridge freezer
It will more than likely need a new door s/w.
The contacts tend to “soot” up on them.
Power off please if having a go :zap:
superfix
ParticipantRe: Bosch T/D Front Panel removal?
Yes Martin, remove fascia panel and side panels (to make life easier).
Once the fascia is removed it becomes quite obvious how to remove the panel.
Don’t forget the long screw in the middle with a cap covering it.
Make sure you have a good look at the mechanicals of the assy as they have a habit of falling apart as you try to remove them :rolls:
Good luck.
superfix
ParticipantRe: Neff integ dish no spray.
😀 😀 😀 😀
I’ll do it for ya.
-
AuthorPosts
