Taff

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 65 total)
1 2 3 4 5
  • Author
    Posts
  • July 31, 2015 at 4:42 pm in reply to: De Dietrich DTI1049X1 Tripping RCD #421408
    Taff
    Participant

    Re: De Dietrich DTI1049X1 Tripping RCD

    The power card was causing the failure

    July 11, 2015 at 5:55 pm in reply to: Indesit TLAA10(UK) over freezing #428442
    Taff
    Participant

    Re: Indesit TLAA10(UK) over freezing

    Further to my request for info on this fridge, I have been reliably informed that this model has a problem with the back Liner as do many other models and brands. Behind the evaporator plate there is aplastic liner which has separated this allows ice to build up on the wet wall. To confirm this the fridge should be defrosted to see if the evaporator plate feels spongy when pushed. If it is there is nothing you can do to correct this failure.

    March 22, 2015 at 9:08 pm in reply to: Cannon C60ETX #425654
    Taff
    Participant

    Re: Cannon C60ETX

    The Board is unprogramed

    March 22, 2015 at 2:57 pm in reply to: Cannon C60ETX #425652
    Taff
    Participant

    Re: Cannon C60ETX

    Thanks for the response. I have contacted Cannon who have confirmed that the F01 fault is the main circuit board. I have had to body swerve this job as the board comes programmed and I don’t have the card reader.

    January 16, 2015 at 11:48 am in reply to: Miele W833 Rinse Light Flashing #423674
    Taff
    Participant

    Re: Miele W833 Rinse Light Flashing

    The machine seems to function correctly just the rinse light flashes?

    September 19, 2014 at 6:56 pm in reply to: Bosch WAE24162UK/08 #419409
    Taff
    Participant

    Re: Bosch WAE24162UK/08

    Thanks for the swift reply which confirms my diagnosis

    June 9, 2014 at 5:43 pm in reply to: Miele Dishwasher G645 SC Plus #414774
    Taff
    Participant

    Re: Miele Dishwasher G645 SC Plus

    Checked the reed switch continuity which was OK. I also jumped out the level switch which is in the circuit but same fault. It looks like the control module as I don’t think there is anything else in the circuit for water intake valve. I have tried a new reed switch.

    June 4, 2014 at 11:14 am in reply to: Miele Dishwasher G645 SC Plus #414771
    Taff
    Participant

    Re: Miele Dishwasher G645 SC Plus

    Hi I have checked the reed switch, should there be a resistance between the terminals. Its open circuit at the moment?

    May 20, 2014 at 8:04 pm in reply to: Bosch WFO2260 Spin Cycle #413945
    Taff
    Participant

    Re: Bosch WFO2260 Spin Cycle

    OK I will give it another go before it hits the skip

    May 19, 2014 at 6:26 pm in reply to: Bosch WFO2260 Spin Cycle #413941
    Taff
    Participant

    Re: Bosch WFO2260 Spin Cycle

    Thanks for the fast reply, is going for scrap as an new module is almost as much as a new machine.

    January 18, 2014 at 8:53 am in reply to: Hotpoint HV7F140 Tripping RCD #407564
    Taff
    Participant

    Re: Hotpoint HV7F140 Tripping RCD

    The connector block was used to extend the mains lead to the machine. So when I was testing it, it should have picked up the fault. The meter was set to 500v, my finger trouble.

    January 17, 2014 at 5:33 pm in reply to: Hotpoint HV7F140 Tripping RCD #407562
    Taff
    Participant

    Re: Hotpoint HV7F140 Tripping RCD

    400v

    January 17, 2014 at 10:17 am in reply to: Hotpoint HV7F140 Tripping RCD #407559
    Taff
    Participant

    Re: Hotpoint HV7F140 Tripping RCD

    Took your advise and tried the mains filter. Fault resolved. I then went to remove the old mains cable from underneath the kitchen unit and blow me if there was a connector block shorting out. What I can’t understand is why the insulation check never showed this fault up. You just can’t put a price on knowledge. Regards Taff

    December 4, 2013 at 7:33 am in reply to: BEKO DCU8230 Sticks in program #405141
    Taff
    Participant

    Re: BEKO DCU8230 Sticks in program

    Yes cleaned the sensor on my first visit.

    December 3, 2013 at 6:39 pm in reply to: BEKO DCU8230 Sticks in program #405139
    Taff
    Participant

    Re: BEKO DCU8230 Sticks in program

    I managed to get back to this job today. I can confirm that the machine consistently remains in the drying cycle turning consistently with the heater on, with the start and drying light on (not flashing) I have meggered the heater and got a result of over 10meg. You mentioned about diagnostics I would appreciate any info. Regards Taff

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 65 total)
1 2 3 4 5