timdowning

Forum Replies Created

Viewing 15 posts - 361 through 375 (of 2,180 total)
  • Author
    Posts
  • in reply to: Whirlpool to do a recall on Hotpoint dryers #431084
    timdowning
    Participant

    Re: Whirlpool to do a recall on Hotpoint dryers

    I think Martin’s post is fair enough, don’t be so harsh Bryan.
    Even if we won’t be directly involved with the recall at least you can warn customers if you bump into one of these dryers. The same as when we all bump into one of the recalled Bosch dishwashers.
    Good customer relations and all that…

    in reply to: WTA listings #432036
    timdowning
    Participant

    Re: WTA listings

    When were the renewals sent out? Ta.

    in reply to: Neff dishwasher door won’t lock #431977
    timdowning
    Participant

    Re: Neff dishwasher door won’t lock

    Have you tried pulling the machine out slightly to make sure its not the wooden door or kitchen unit that’s interrupting things?

    in reply to: Should we Refund #431943
    timdowning
    Participant

    Re: Should we Refund

    Maybe the customers waiting to hear back from TS too…

    🙂

    That was a joke, lets hope they have gone to hassle someone else.

    in reply to: Product Recalls #431973
    timdowning
    Participant

    Re: Product Recalls

    What are the chances of them using an ISE machine, they had 8 million Hotpoint’s to choose from.

    in reply to: WF860P NOT SPINNING #431724
    timdowning
    Participant

    Re: WF860P NOT SPINNING

    Thanks for putting it so eloquently Martin.
    I was in a bit of rush, I was having to keep my eye on Easy jet as they were releasing their Summer flights early this morning.

    in reply to: WF860P NOT SPINNING #431722
    timdowning
    Participant

    Re: WF860P NOT SPINNING

    The heater being open circuit is a possible cause of a no spin. So disconnecting it doesn’t prove anything.

    in reply to: WF860P NOT SPINNING #431720
    timdowning
    Participant

    Re: WF860P NOT SPINNING

    I would be checking the heater.

    in reply to: Indesit IDC75UK Drive Belt #430991
    timdowning
    Participant

    Re: Indesit IDC75UK Drive Belt

    Just put the belt on the pulley and with your hand pull the pulley and belt at the same time onto the pulley shaft.

    in reply to: Beko WDA91440W Washer Dryer #430570
    timdowning
    Participant

    Re: Beko WDA91440W Washer Dryer

    The manual only says;
    • Loading door of the machine may not be opened due to safety reasons. >>> If “wait to cool down to open….”
    warning is displayed, machine will keep the loading door locked for your safety until it cools down. You can accelerate
    cooling by running any 10-minute drying programme.

    Has the air intake filter been cleaned?

    in reply to: NEFF W5440X0GB/27 #430881
    timdowning
    Participant

    Re: NEFF W5440X0GB/27

    660 Mohms, the heaters fine!!

    Did you check the thermistor wiring where it is tied to the tub? If wiring is ok then I change the thermistor as a matter of course. Then it only leaves the module that could be your problem.

    in reply to: Cannon C60EKS #430666
    timdowning
    Participant

    Re: Cannon C60EKS

    Thanks.

    in reply to: How does ‘Cashback’ work? #430671
    timdowning
    Participant

    Re: How does ‘Cashback’ work?

    No affect to the retailer at all.
    The manufacturer is the one that takes the hit.

    in reply to: Bosch Dishwasher SMV50C00GB/03 Fault codes #430667
    timdowning
    Participant

    Re: Bosch Dishwasher SMV50C00GB/03 Fault codes

    Does it bring on the check water light?
    If it drains ok. Then try the flow meter in the side tank.
    Other than that look at the door locking side of things. Sometimes if its the door, opening and closing it every 10 seconds until you here the water valve open can prove door or door hinge issues.

    in reply to: Cannon C60EKS #430664
    timdowning
    Participant

    Re: Cannon C60EKS

    Cheers for reply, Is the hob screwed in or clipped? Just need to know I’m prising in the right places.

Viewing 15 posts - 361 through 375 (of 2,180 total)