timdowning

Forum Replies Created

Viewing 15 posts - 76 through 90 (of 2,180 total)
1 2 3 … 5 6 7 … 144 145 146
  • Author
    Posts
  • March 15, 2018 at 5:44 pm in reply to: Qualtex game? #434742
    timdowning
    Participant

    Re: Qualtex game?

    The gifts are back.
    Second week running.

    Mug & a coaster.
    No games yet.

    March 14, 2018 at 2:01 pm in reply to: Hotpoint fixing spring tool #454711
    timdowning
    Participant

    Re: Hotpoint fixing spring tool

    I appreciate your kindness.

    March 14, 2018 at 1:51 pm in reply to: Hotpoint fixing spring tool #454709
    timdowning
    Participant

    Re: Hotpoint fixing spring tool

    Cheers Jim.

    That’s £15 less made on that job.

    Grr.

    March 14, 2018 at 6:48 am in reply to: Ise 5 still going strong #454678
    timdowning
    Participant

    Re: Ise 5 still going strong

    Good old Beko.

    March 13, 2018 at 3:00 pm in reply to: Bosch won’t wash ( D/W) #454652
    timdowning
    Participant

    Re: Bosch won’t wash ( D/W)

    Access through the front panel with kitchen door off.
    No need to pull it out if it’s just the transfer hose…

    March 9, 2018 at 7:44 pm in reply to: ISE10 1606W bearings #454371
    timdowning
    Participant

    Re: ISE10 1606W bearings

    Just out of interest what did they quote for replacing the bearings?

    February 26, 2018 at 7:52 pm in reply to: Hoover DXA48W3/1-80 No display #454259
    timdowning
    Participant

    Re: Hoover DXA48W3/1-80 No display

    I’m sure you have but just fully unplug it for 5 minutes.

    February 26, 2018 at 4:44 pm in reply to: Bosch WTE84106GB/48 #454255
    timdowning
    Participant

    Re: Bosch WTE84106GB/48

    Probably a sludged up sump / pump.
    (Doubtful it’s a sensor. )

    February 24, 2018 at 6:11 am in reply to: February 2018 WTA conference #451204
    timdowning
    Participant

    Re: February 2018 WTA conference

    Aside the biscuits.

    Is there any update – main points for those WTA members that couldn’t attend?

    Thanks.

    February 23, 2018 at 3:05 pm in reply to: Hotpoint drier eating jockey pulleys. #454204
    timdowning
    Participant

    Re: Hotpoint drier eating jockey pulleys.

    I always fit the tension pulley from the TL61 old type dryers.
    I did notice that the picture of the CTD00 pulley seems to come with a ball bearing now?

    February 21, 2018 at 4:51 pm in reply to: neff warming drawer #454160
    timdowning
    Participant

    Re: neff warming drawer

    As above, parts are so expensive…

    February 21, 2018 at 6:32 am in reply to: Beko WDIR7543101 #453955
    timdowning
    Participant

    Re: Beko WDIR7543101

    Just an update on this –

    By the time I got to see the machine it had worked perfectly for a couple of goes.

    I thought I would run it in service mode but the combination of buttons it suggested didn’t work??

    I then set about checking all cables but unfortunately no breaks found.

    The only thing I did notice were signs of water leaking from the little vent on top of the dryer heater box. I guessed that this could be causing water to drip down onto the module at the bottom right Not wanting to block the vent hole up, which I was tempted to do, I fitted a 2 inch piece of rigid rubber hose on it so that hopefully the height of the hose would be enough for water not to make its way up…

    We shall see.

    February 19, 2018 at 8:29 pm in reply to: Plug in power meter #454074
    timdowning
    Participant

    Re: Plug in power meter

    Just have a 13 amp extension lead made up with the
    part of the insulation removed so you can clamp the meter onto the live…

    February 15, 2018 at 6:48 am in reply to: Qualtex Account Closure #443621
    timdowning
    Participant

    Re: Qualtex Account Closure

    Connect are doing well out of me lately because of it.

    February 14, 2018 at 6:26 pm in reply to: Beko WDIR7543101 #453954
    timdowning
    Participant

    Re: Beko WDIR7543101

    Excellent, I’ll see how I go with the concise version.
    Cheers.

  • Author
    Posts
Viewing 15 posts - 76 through 90 (of 2,180 total)
1 2 3 … 5 6 7 … 144 145 146