Forum Replies Created
-
Posts
-
Re: Liebherr CNesf 3033 fault help
There are no tests you can perform on the board to test the board itself, take the mains plug out first, to replace board remove the covers to the left and right of the panel ( they clip on ) then remove the two torx screws holding the facia panel in place.
The sensor and power cables need to be removed from the ends of the board by pressing down on the tabs directly behind them and the white connectors can be pulled off in a backwards motion complete, unplug other connections on the top of the board, then push out the control knobs from the potentiometers, BE CAREFULL. The facia and board holder is made up in two sections which again unclip, then remove board by lifting gently while depressing holding clips, glass reed sensor needs to be removed ( it is connected to the grey bus cable ) and fits between the two sections, Its made of glass treat it with care.
It may help to take pictures as you go to remember how to put it back together and make sure the board is the right way round along with the two sections of the facia panel and where all your connections need to go.Re: Liebherr CNesf 3033 fault help
I have seen this issue before, all the connections for interior light and sensors power off the integral board, the part number is 6113821, Liebherr GB do not have one in stock at the moment, but try the guys here at ukwhitegoods, it is listed on their parts system and is cheaper than Liebherrs screen price of £177 plus vat and postage.
http://www.liebherr-randallrefrigeration.co.uk/Re: Liebherr CNesf 3033 fault help
Sounds like the integral board is faulty..
http://www.liebherr-randallrefrigeration.co.uk/Re: Liebherr CUN 3913 not cooling properly
Issue date 19102009
Model designation CUN 3913-21E
Design 147
External designation
Model series FRIDGE-FREEZER-FR. COMP. AT BOTTOM-NOFROST
Service number 098108605
Production period 24092009 – 18102009Re: Liebherr CUN 3913 not cooling properly
Week 13 year 2008, board production period made prior to the cabinet.
Re: Liebherr CUN 3913 not cooling properly
When you state you measured the sensors, how did you do this ?
This units production period was 24.9.2009 to 18.10.2009, older than you thought.
http://www.liebherr-randallrefrigeration.co.ukRe: Liebherr bio-fresh/freezer
Temperature setting range: The temperature is automatically controlled and is kept constant at just above 0°C. It may, however, be changed slightly: Press Alarm button (5) for approx. 8 seconds. The letter “b” will appear in the BioFresh display (8) and the current setting will be shown in the freezer display (1). Now press the temperature setting buttons (2). The temperature can be changed by +/- 5 increments. Each adjustment interval reduces or increases the temperature by approx. 0.5 K. The setting mode is disabled by pressing the Alarm button.
Re: Liebherr integrated larder fridge not cooling
There are plastic covers each end of the display panel, unclip these and you will find screws, the panel then can be pulled forward gently for access to both boards.
Liebherr are showing no stock in the UK, but it may be available in Germany. I managed to get a board last year for exactly the same problem you have.Re: Faulty Freezer – not cooling, please help.
Could be short on gas, but more likely a restriction in the filter drier, Engineer needed trained and certified to work with R600A gas.
Re: Liebherr integrated larder fridge not cooling
Fan and light switch are one unit, so if light goes out guess switch is OK.
Have you replaced front board yet?Re: Liebherr Comfort refrigerator freezes.
This is a Liebherr commercial freezer, the 2 dashes indicate the unit is not at the correct temperature, you need to find out why the compressor is not running.
Is it losing voltage or is it or the relay failed. Only an inspection by an Engineer can tell you what has failed.Re: Miele KFN12924SD warm fridge
It could be the evaporator sensor, which is foamed in on this model, it activates the valve to send refrigerant to the fridge section, the sensor kit will need fitting to the rear board and is supplied with a new cover for fitting the sensor inside the fridge.
Easy for an Engineer, tricky for a non trades person.
http://www.liebherr-randallfrigeration.comRe: Liebherr integrated larder fridge not cooling
I would also check that the door is closing correctly to operate the fan switch and that the fan connector plug is not corroded, and the fan switch is working.
Re: Liebherr integrated larder fridge not cooling
Morning,
The part number is 6113652.
Regards,
Tony.
http://www.liebherr-randallrefrigeration.co.uk
