Washman

Forum Replies Created

Viewing 15 posts - 136 through 150 (of 894 total)
1 2 3 … 9 10 11 … 58 59 60
  • Author
    Posts
  • August 25, 2011 at 8:37 am in reply to: working on gas cookers information #357669
    Washman
    Participant

    Re: working on gas cookers information

    Hi

    I have just spoken to the GAS SAFE tecnical department , and they say it is perfectly safe to carry out electrical work on a gas/dual fuel appliance and even disconnect the bayonet fitting to gain access the appliance,as long as no other part of the gas system is touched.As disconnecting the bayonet fitting is not considered as part of the gas system.

    Mike

    August 24, 2011 at 7:07 pm in reply to: Zanussi FJ1295 Short Spin problem #357717
    Washman
    Participant

    Re: Zanussi FJ1295 Short Spin problem

    Hi

    Have you got the Rinse hold button pressed in ,
    No drain (Rinse Hold): stops the appliance with water in the tub after the last rinse of the
    SYNTHETICS, DELICATES and WOOLLENS. By pressing the push button again, the cycle is
    completed with a drain and a short spin; on the washer dryers the drying is also performed .

    Washman

    August 11, 2011 at 5:36 pm in reply to: Leaking Zanussi Aquacycle 100 – advise please #357112
    Washman
    Participant

    Re: Leaking Zanussi Aquacycle 100 – advise please

    Hi

    Full model number and PNC number will help us help you.

    Washman

    August 10, 2011 at 11:57 am in reply to: Hotpoint C367EWH Main Oven Not Working #357063
    Washman
    Participant

    Re: Hotpoint C367EWH Main Oven Not Working

    Hi

    Check the clock is set to manual, if set to auto nothing works unless you set a start time and an end time.

    Washman

    August 10, 2011 at 11:33 am in reply to: Zanussi zce7551 main oven faulty #357068
    Washman
    Participant

    Re: Zanussi zce7551 main oven faulty

    Hi

    How are you checking the voltage at the fan motor and element, because you they are OK and you are getting 230 volt across terminals it should work. Unless they are open circuit

    MIke

    August 4, 2011 at 6:37 pm in reply to: Cooker hood extractor spigot #356636
    Washman
    Participant

    Re: Cooker hood extractor spigot

    Hi

    No it is not advisable to do this. Just fit grease and charcoal filters and let it reciculate the air.

    Washman

    August 4, 2011 at 6:28 pm in reply to: siwamat 5100 does not spin out #356710
    Washman
    Participant

    Re: siwamat 5100 does not spin out

    Hi

    It will not spin until all the water is gone,so you need to check the filter and drain pipe.

    Washman

    August 3, 2011 at 6:45 pm in reply to: Hoover OPH714D Service manual required #356656
    Washman
    Participant

    Re: Hoover OPH714D Service manual required

    Hi

    Thanks Bob, will change heater and see what happens.

    Mike

    July 31, 2011 at 10:27 am in reply to: Hotpoint washer/dryer WD420G Help required please! #356378
    Washman
    Participant

    Re: Hotpoint washer/dryer WD420G Help required please!

    Hi
    Please read the rules at begining of this forum

    Rule 8/ Please do not ask for wiring diagrams, schematics or for us to sort out any wiring problems over the internet. We cannot judge how competent you are nor the future readers of any thread, we’ll try to point you in the right direction but that’s as far as we can legally go.

    Washman

    June 22, 2011 at 11:55 am in reply to: Indesit DI67S PCB #354008
    Washman
    Participant

    Re: Indesit DI67S PCB

    Hi

    I would go with the £100.00 quote with one year warranty.
    You wont get one year warranty if you buy the PCB privately,and also you have to be sure there is no other problem with machine that will blow new PCB when you fit it.So its at your own risk if you fit PCB and it blows.

    Washman

    June 13, 2011 at 10:22 am in reply to: Servis M3810s Bearing Kit #352817
    Washman
    Participant

    Re: Servis M3810s Bearing Kit

    Hi

    You do not need to remove the drum spider from the drum to change the bearings, once you have back plate off with the drum and pulley is off just tap the spider out of the back plate.Taking care not to damage the shaft, then you can get at the bearings.

    Washman

    June 6, 2011 at 5:57 pm in reply to: Leisure Cookmaster 100 – CM10FRC #352433
    Washman
    Participant

    Re: Leisure Cookmaster 100 – CM10FRC

    Hi

    Where the picture in the above post shows the new style stat is there a wire clamped to that bracket, the original stat is no longer avaliable. You just cut out the original and replace with the new one and new crimp on terminals.

    Turn off power first.

    Washman

    June 6, 2011 at 5:46 pm in reply to: Belling Farmhouse 930 Electric. Parts Needed #352950
    Washman
    Participant

    Re: Belling Farmhouse 930 Electric. Parts Needed

    Hi

    You need to remove the Warming/storage drawer completely to find the numbers .

    Washman

    June 4, 2011 at 7:03 pm in reply to: Bosch SGS3042GB/03 – timer sticking #352539
    Washman
    Participant

    Re: Bosch SGS3042GB/03 – timer sticking

    Hi

    Complete heater assembly only . No individual parts avaliable from Bosch for this.

    Washman

    May 26, 2011 at 5:47 pm in reply to: Whirlpool top loader #350434
    Washman
    Participant

    Re: Whirlpool top loader

    Hi

    Go to http://appliancejunk.com/forums/index.php?topic=6354.0 its an American site with video on changing all parts .

    Mike

  • Author
    Posts
Viewing 15 posts - 136 through 150 (of 894 total)
1 2 3 … 9 10 11 … 58 59 60