Washman

Forum Replies Created

Viewing 15 posts - 331 through 345 (of 894 total)
1 2 3 … 22 23 24 … 58 59 60
  • Author
    Posts
  • May 28, 2009 at 3:53 pm in reply to: Samsung J845 wont spin. shows ‘UE’ fault #287992
    Washman
    Participant

    Re: Samsung J845 wont spin. shows ‘UE’ fault

    Hi

    One item is not enough to try and spin, you need at least half a load so that it can be distributed around the the drum before spin.
    Out of balance is controled by the PCB main board sensing how the motor is turning.

    Washman

    May 28, 2009 at 3:45 pm in reply to: Smeg DWF612ss #287962
    Washman
    Participant

    Re: Smeg DWF612ss

    Hi

    Container with brown looking crystals is correct thats the water softener, thats where the salt goes through to regenerate.

    Washman

    May 28, 2009 at 1:33 pm in reply to: Electrolux EOB944W1 #273859
    Washman
    Participant

    Re: Electrolux EOB944W1

    Hi

    See forum rules

    7/ Technical information. This is very often specifically copyright to a given manufacturer and will not be publically quoted in the forums.

    8/ Please do not ask for wiring diagrams, schematics or for us to sort out any wiring problems over the internet. We cannot judge how competent you are nor the future readers of any thread, we’ll try to point you in the right direction but that’s as far as we can legally go.

    Washman

    May 28, 2009 at 1:28 pm in reply to: Samsung J845 wont spin. shows ‘UE’ fault #287989
    Washman
    Participant

    Re: Samsung J845 wont spin. shows ‘UE’ fault

    Hi

    From Error Code Identification Sheet

    ” UE ” Cause Unbalanced Error . =The load in the drum is unbalanced.

    Solution = Switch off the power and rearrange, add,or remove some of the items to be washed.

    May 26, 2009 at 2:19 pm in reply to: servis m6000/1 #287867
    Washman
    Participant

    Re: servis m6000/1

    Hi

    Most likely a module fault .

    Mike

    May 26, 2009 at 9:01 am in reply to: Candy DSI 795XF parts diagram for control panel #287559
    Washman
    Participant

    Re: Candy DSI 795XF parts diagram for control panel

    Hi

    41005585 comes up as timer knob not control panel

    Mike

    May 25, 2009 at 6:29 pm in reply to: rangemaster #287846
    Washman
    Participant

    Re: rangemaster

    Hi

    From memory , remove plastic end caps from control panel they just pull off,then undo one screw from each side panel and ease panel out there should then be one screw each side holding hob glass ,remove screws and hob should hinge up ,you will need support to hold top up.

    Mike

    May 25, 2009 at 2:57 pm in reply to: Candy DSI 795XF parts diagram for control panel #287557
    Washman
    Participant

    Re: Candy DSI 795XF parts diagram for control panel

    Hi

    Sorry for delay been away for the weekend. Items 21 and 10 required.

    Thanks Mike

    May 21, 2009 at 1:16 pm in reply to: Electra AWM1100Beco not heating up #287374
    Washman
    Participant

    Re: Electra AWM1100Beco not heating up

    Hi

    Electra was also a brand that Servis uk were selling AWM110BE comes up as a Servis machine from about 2003, whats the serial number? can then check details.

    Mike

    May 20, 2009 at 5:45 pm in reply to: Belling Cooker 492SS #287414
    Washman
    Participant

    Re: Belling Cooker 492SS

    Hi

    Have a look at 4belling.co.uk they have listed Glass:door-outer lower oven 492SS £104.99 delivery within 7 days.

    Mike

    May 20, 2009 at 5:05 pm in reply to: Belling Cooker 492SS #287410
    Washman
    Participant

    Re: Belling Cooker 492SS

    Hi

    There is a Belling model XOU492ss

    Mike

    May 18, 2009 at 12:00 pm in reply to: no work #287013
    Washman
    Participant

    Re: no work

    Hi

    Very quiet here as well, one job today and one booked for tomorrow so far. Only did 8 jobs last week.

    Mike

    May 18, 2009 at 8:57 am in reply to: Sharp R98 Combi oven– bulb has blown #286948
    Washman
    Participant

    Re: Sharp R98 Combi oven– bulb has blown

    Hi

    DO NOT attempt to take microwave apart to replace lamp .
    Microwaves can kill even when switched off .Very high voltage stored in main capacitor up to 4000 volts .
    Call a microwave engineer out .

    Washman

    May 15, 2009 at 6:36 pm in reply to: Diplomat Dishwasher warning light #286841
    Washman
    Participant

    Re: Diplomat Dishwasher warning light

    Hi

    Model number and serial number would help.

    Washman

    May 14, 2009 at 1:10 pm in reply to: NEFF U1744N0GB Switch Malfunction #286485
    Washman
    Participant

    Re: NEFF U1744N0GB Switch Malfunction

    Hi

    200 degrees is the highest setting most fan ovens go to. With a fan oven you cook at a lower temperature and for less time than a conventional oven, cooking with a fan oven is cheaper ie:-less heat less time = less money spent on cooking.

    Washman

  • Author
    Posts
Viewing 15 posts - 331 through 345 (of 894 total)
1 2 3 … 22 23 24 … 58 59 60