Washman

Forum Replies Created

Viewing 15 posts - 346 through 360 (of 894 total)
  • Author
    Posts
  • Washman
    Participant

    Re: ISE10, rinsing, quality, reliability and cost of repairs

    Hi

    Nobody can say how much a washing machine or
    any thing else is going to cost to repair in 10 years time , what will wages be and what will inflation be .Thinking 10 years ahead you would need a crystal ball , to find that out.
    It will also depend on how well you look after the machine and maintain it during that time as well .

    Washman

    in reply to: Bosch drain pump #286226
    Washman
    Participant

    Re: Bosch drain pump

    Hi

    The number you had was wrong it should be WFO2465GB/01.

    P no 142370 £57.51 less discount +vat+p/p

    Mike

    in reply to: Whirlpool Tumble Dryer 3RLER5437KQ3 cuting out #286131
    Washman
    Participant

    Re: Whirlpool Tumble Dryer 3RLER5437KQ3 cuting out

    Hi

    Last one of these I did with this problem I had to replace the motor.

    Mike

    in reply to: DIPLOMAT APM8703/2 WASHERDRYER #286108
    Washman
    Participant

    Re: DIPLOMAT APM8703/2 WASHERDRYER

    Hi

    They will only supply the disk if you open an account with them.

    Mike

    in reply to: Connections – Price bands #285876
    Washman
    Participant

    Re: Connections – Price bands

    Hi

    Mine comes out at

    PMP666 £6:36
    MER077118 £38:40
    HVR90489300 £5:51
    WPL481225928681 £7:36

    Mike

    in reply to: Hotpoint WML520P Leaking from Drawer #282723
    Washman
    Participant

    Re: Hotpoint WML520P Leaking from Drawer

    Hi

    Calgon will be no good in dispenser ,as water in dispenser is incoming flow. Calgon goes in drum so only cleans the drum.

    Mike

    in reply to: Zanussi FLA 1201W lost its ooomph in the spin cycle #282570
    Washman
    Participant

    Re: Zanussi FLA 1201W lost its ooomph in the spin cycle

    Hi

    Wet bath mat is not the best thing to use as a test . Try a normal load and see if this makes a difference.

    Mike

    in reply to: WF740 #282508
    Washman
    Participant

    Re: WF740

    Hi
    ——————————————————————————–
    .
    H20 – Time out – fill (taps) check inlet valves and pressure chamber

    Mike

    in reply to: whirlpool element #282061
    Washman
    Participant

    Re: whirlpool element

    Hi

    481225928823 is £34.27 from Electrue/Connections.

    Mike

    in reply to: samsung q1433s #281515
    Washman
    Participant

    Re: samsung q1433s

    Hi

    Thats the water level control switch.

    Washman

    in reply to: siemens waher dryer part enquiry #281460
    Washman
    Participant

    Re: siemens waher dryer part enquiry

    Hi

    Please post model and serial numbers.

    Polystyrene disc is anti flood device, if machine leaks into base disc rises and switches water inlet valves off and drain pump on.

    Mike

    in reply to: asko 12004 Thermostat #280684
    Washman
    Participant

    Re: asko 12004 Thermostat

    Hi

    Try Armstrongs – 01635 33881

    Mike

    in reply to: Hotpoint Fridge #280485
    Washman
    Participant

    Re: Hotpoint Fridge

    Hi

    Ice or frost .It should get a layer of frost then when the compressor shuts down it should then defrost the plate completely before starting up again.
    Bananas should be at room temperature if yellow or chilled if green to stop them ripening and turning yellow.

    Mike

    in reply to: is there no contact number for SERVIS anymore? #279984
    Washman
    Participant

    Re: is there no contact number for SERVIS anymore?

    Hi

    Servis has gone bust , so the retailer is responsible for repairs or replacement of appliance.

    Mike

    in reply to: servis washer dryer #279999
    Washman
    Participant

    Re: servis washer dryer

    Hi

    Part number is on all Servis modules it starts 546*******.

    Mike

Viewing 15 posts - 346 through 360 (of 894 total)