Washman

Forum Replies Created

Viewing 15 posts - 376 through 390 (of 894 total)
  • Author
    Posts
  • in reply to: Beko DE3431FW sump sensor probe #277029
    Washman
    Participant

    Re: Beko DE3431FW sump sensor probe

    Hi

    It senses the water temperature, so controler knows when to switch heater off.

    Washman

    in reply to: apm8552 #276003
    Washman
    Participant

    Re: apm8552

    Hi

    Back panel bearing assembly 718013000 complete

    Mike

    in reply to: apm8552 #276002
    Washman
    Participant

    Re: apm8552

    Hi

    75026770 bearing seal.

    Mike

    in reply to: BEKO DVC 665 s Electric Cooker GOOSED #276914
    Washman
    Participant

    Re: BEKO DVC 665 s Electric Cooker GOOSED

    Hi

    dont want to be ripped off by engineers

    But OK to get free advice from Engineers.

    Washman

    in reply to: apm8552 #275999
    Washman
    Participant

    Re: apm8552

    Hi

    Just looked on service manual and it lists 720344000 drum and shaft and 402017200 tub gasket.

    Mike

    in reply to: WTL6102gb02 No Heat #276782
    Washman
    Participant

    Re: WTL6102gb02 No Heat

    Hi

    You need to test these with a damp load , will not run for long if no load.

    Mike

    in reply to: Hotpoint WM12 won’t complete program #276692
    Washman
    Participant

    Re: Hotpoint WM12 won’t complete program

    HI

    Check motor brushes.

    Switch off and plug out first.

    Mike

    in reply to: Frost developing inside back of fridge #276479
    Washman
    Participant

    Re: Frost developing inside back of fridge

    Hi

    I’m sure the Beko CDA563FS is frost free freezer and refrigerated back panel in fridge, so a layer of frost will form on back panel of fridge. This should just defrost each time the compressor stops. According to description of this appliance the fridge has ” Concealed evaporator with cold wall technology “Automatic defrost in fridge . So appliance may be working correctly.

    Mike

    in reply to: Bosch SG51312GB/12 – New Module does not respond #276363
    Washman
    Participant

    Re: Bosch SG51312GB/12 – New Module does not respond

    Hi

    Did you follow all instructions and program module correctly.

    Mike

    in reply to: CDA repair or new machine? #276381
    Washman
    Participant

    Re: CDA repair or new machine?

    Hi

    Have you checked the filter,as a blocked filter will stop machine from spinning

    Mike

    in reply to: AEG Competance Oven not heating up #276303
    Washman
    Participant

    Re: AEG Competance Oven not heating up

    Hi

    When set to fan it uses a different element to conventional setting.

    Washman

    in reply to: Servis MV6000W Door Seal #276160
    Washman
    Participant

    Re: Servis MV6000W Door Seal

    Hi

    The MV models were made by Vestel for Servis.

    Mike

    in reply to: servis m6500w-1. pump req #276006
    Washman
    Participant

    Re: servis m6500w-1. pump req

    Hi

    What about a standard Plaset or Askoll pump motor.

    Mike

    in reply to: Help please, looking for interlock for Servis M9409W #275709
    Washman
    Participant

    Re: Help please, looking for interlock for Servis M9409W

    Hi

    Serial no starting 9947 means it was made in week 47 of 1999.

    First four digits of Servis serial number are year and week number.

    Mike

    in reply to: Beko WMA 520W #275735
    Washman
    Participant

    Re: Beko WMA 520W

    Hi

    Pat test is no good ,you need to test all components seperatley.

    Mike

Viewing 15 posts - 376 through 390 (of 894 total)