[Washman]

Re: Hoover WB120 001 hot water temp

Hi

Have you actually checked the temperature of the water with a thermometer during the wash part of cycle , or are you just touching door glass. Also on 40/60 deg washes if total amount of water is 4 gallons of this 3 gals will be cold water and 1gal of hot. Because cold water is usually at mains pressure and hot is gravity fed from hot water tank.
A lot of new machines are now cold fill only,
And do not forget that machine will do 3 or 4 rinses with cold water at the end before spinning

[Washman]

Re: carbon brushes for tricity bendix

Hi

Full model number required and PNC number from label

[Washman]

Re: Sevis M6050W Dead

Hi

It could be the PCB behind the buttons this can cause a dead machine.
Part no 502020600 Electronic button PCB

Hope this helps

Mike

[Washman]

Re: Beko WMA1715S

Hi

Beko washing machine reset

the fix for flashing pre wash led, or flashing start/cancelbutton is

Turn power button off (not at wall)
Select 90 degree wash
Press Start and Cancel button down at same time for 3 seconds and turn power button on whilst still holding buttons down – Start light will flash.
Leave power on.
Select any Spin position.
Press Start and Cancel button at same time again for 3 seconds – other buttons may start to flash – if they do, press Start and Cancel button together again for 3 seconds.
Machine should be re-set ready for use.

Mike

[Washman]

Re: Servis M9209 – are these “issues” normal ❓

Hi

Dryer fan Part no 268010200 is required .
Machine will work OK as a washer but the dryer will not work without the fan. Posibily time for engineer to check out machine to find out why fan broke up

POWER OFF BEFORE OPENING UP MACHINE

Mike

[Washman]

Re: Servis M9209 – are these “issues” normal ❓

Hi

It sounds as though you do need to clean the filter.
If machine cannot pump out water it will abort the program.
To get the filter out you just have to unscrew it and pull , if its tight its because it needs cleaning, so have plenty of towells around.

Mike

[Washman]

Re: Samsung P1253 Problem

Hi

Check your user manual Samsung washing machines should have a two year guarrantee . Phone Samsung with model and serial numbers both found on rear of machine. And have proof of purchase ie:invoice or delivery note handy. Just tell them it will not drain and is noisy .

Mike

[Washman]

Re: Servis M3024/M Thermostat

Hi

Sorry you are right, it is a washer only the stat no is correct

Mike

[Washman]

Re: FEEDBACK??????

Hi
On the home page Trade forums (Trade only )
Instructions to create an account, if you need help, are given in the first link in the “Information” box to the left of this message or using the “create one” link below the login panel to the right which you can see on the homepage. If you have any problems please do not hesitate to contact site administration for additional help should you require any either by email or using the “feedback” from the navigation panel on the left.

Washman

[Washman]

Re: ASEA WASHING MACHINE 9600

Hi

This machine is at least 20 years old and bearing were a pain .
you need
O-ring p/no 8901760
thrower ring p/no 8008474
V-ring p/no 33600404
washer p/no 33257439
and two bearings p/no 33600415

if you get them , better still sell them a new machine .

Mike

[Washman]

Re: Servis M3024/M Thermostat

Hi

Its a DOMAR made washer dryer model and serial no’s match up
picture shows two
fixed stat part no 526001300
thermo resistance part no 526011900

Mike

[Washman]

Re: Zanussi Fan Oven – New Element, No Heat

Hi

Have you reset clock to manual and not to auto

Mike

[Washman]

Re: Servis M3510 S

Hi

The 2 White wires connect to thermister and the 2 grey wires to stat side.
Just use meter to find correct terminals ie:- stat will be a dead short ,thermister will show a resistance

Mike

[Washman]

Re: Help with PCB part

Hi

Make and model number and serial number would help

click on this link http://www.ukwhitegoods.co.uk/modules.p … ic&t=12319

Mike

[Washman]

Re: Zanussi TD201 Tumble Dryer ?

Hi

Main element is in circuit all the time ,the other element is only on or off depending on selected position of the switch ie: in or out.

[Author]

Posts