allan73

Forum Replies Created

Viewing 15 posts - 331 through 345 (of 497 total)
1 2 3 … 22 23 24 … 32 33 34
  • Author
    Posts
  • September 25, 2010 at 5:32 pm in reply to: zanussi keep pauseing #330960
    allan73
    Participant

    Re: zanussi keep pauseing

    As Aqualectric say’s this is a common problem with Zan wd’s most often if dryer is little used.
    I think there are several posts on here regarding this.

    September 25, 2010 at 5:17 pm in reply to: hotpoint tcm570 blowing stats #331244
    allan73
    Participant

    Re: hotpoint tcm570 blowing stats

    Thanks A1, I had kinda narrowed it down to that but it’s good to have confirmation 😉 , do you know if this is a fairly common problem on these ?

    September 25, 2010 at 4:38 pm in reply to: hotpoint tcm570 blowing stats #331242
    allan73
    Participant

    Re: hotpoint tcm570 blowing stats

    Can anyone advise me on this ❓

    September 25, 2010 at 12:11 pm in reply to: hoover oph714d/1-80 #331255
    allan73
    Participant

    Re: hoover oph714d/1-80

    Was the board pre-configured ?

    September 25, 2010 at 8:27 am in reply to: Bosh WFK2801GB/01 1min in display #331162
    allan73
    Participant

    Re: Bosh WFK2801GB/01 1min in display

    Thanks boselecta, I’ll check the usual suspects. 😉

    September 25, 2010 at 6:48 am in reply to: Bosh WFK2801GB/01 1min in display #331160
    allan73
    Participant

    Re: Bosh WFK2801GB/01 1min in display

    Can anyone help me out on this it’s quite far away so I was hoping to go pre armed with info ❓
    I was thinking pump intermittent maybe ❓

    September 24, 2010 at 11:32 am in reply to: Hotpoint WT960 Not taking conditioner #331089
    allan73
    Participant

    Re: Hotpoint WT960 Not taking conditioner

    Sorry to highjack your post grooster but do you know a affective way of cleaning out the channels inside those housings, Ive got an indesit not taking conditioner to look at ❓

    September 24, 2010 at 9:17 am in reply to: Whirlpool awz 410 Help #331113
    allan73
    Participant

    Re: Whirlpool awz 410 Help

    Is it a servis built m?c ?
    If so I’d think it’s the module, but if you squeeze up all the connections to the mod it might do the trick.

    September 24, 2010 at 6:44 am in reply to: Whirlpool awz 410 Help #331111
    allan73
    Participant

    Re: Whirlpool awz 410 Help

    Does it lock the door ?

    September 22, 2010 at 10:38 am in reply to: 10 year warranty on LG direct drive motor. #330080
    allan73
    Participant

    Re: 10 year warranty on LG direct drive motor.

    And did any of these customers choose to take it further Jess1ca ?

    September 18, 2010 at 12:37 pm in reply to: Hotpoint Wd440 no go #330610
    allan73
    Participant

    Re: Hotpoint Wd440 no go

    Have you tugged on the wireing plug to the motor ? Pull on each wire.

    September 17, 2010 at 8:35 pm in reply to: Ariston slimline LSI 45/50 drain pump #330549
    allan73
    Participant

    Re: Ariston slimline LSI 45/50 drain pump

    Thanks, will do.

    September 17, 2010 at 2:35 pm in reply to: Ariston slimline LSI 45/50 drain pump #330547
    allan73
    Participant

    Re: Ariston slimline LSI 45/50 drain pump

    Can anyone help me on this ?

    September 16, 2010 at 9:12 am in reply to: bosch wae24162gb/03 #330298
    allan73
    Participant

    Re: bosch wae24162gb/03

    £80 for the pcb, sounds good to me 😯

    September 15, 2010 at 9:31 am in reply to: Hotpoint TDL11P Front Drum Seal coming off. #330379
    allan73
    Participant

    Re: Hotpoint TDL11P Front Drum Seal coming off.

    I’ve come across these dryers with no bearing pads, don’t know why bearing band is coming off though can you not stick it with some heat resistant adhesive ❓

  • Author
    Posts
Viewing 15 posts - 331 through 345 (of 497 total)
1 2 3 … 22 23 24 … 32 33 34