Bernie

Forum Replies Created

Viewing 15 posts - 196 through 210 (of 289 total)
1 2 3 … 13 14 15 … 18 19 20
  • Author
    Posts
  • November 23, 2009 at 8:14 am in reply to: Ariston A1636 no fast spin #304308
    Bernie
    Participant

    Re: Ariston A1636 no fast spin

    Thanks for that twinspark

    Bernie

    November 11, 2009 at 5:48 pm in reply to: w’pool top loader (3rlsq8000) #302965
    Bernie
    Participant

    Re: w’pool top loader (3rlsq8000)

    I have just had one leaking from tub on spin; the outer tub had a small spilt in it near the top.
    The balance weight that sits on the top of the tub had come lose and had cut a split in the tub. I just patched it.
    With the cabinet off you would see it. Just had a look on Whirlpool CD and there is a gasket listed it goes on the top (Part No. 481946669993) never had to fit one though.


    Bernie

    November 11, 2009 at 11:00 am in reply to: hoover pump #303184
    Bernie
    Participant

    Re: hoover pump

    It might be that the CIW 100 is a washer dryer and there for have a different thermal cutout in the pump?

    It’s only a guess

    Bernie

    October 28, 2009 at 5:55 pm in reply to: Beko WM5120W Motor part no. #300704
    Bernie
    Participant

    Re: Beko WM5120W Motor part no.

    Thanks A1engineer for the quick reply.

    Bernie

    October 8, 2009 at 7:54 am in reply to: Zanussi ZWX1605 error codes #298515
    Bernie
    Participant

    Re: Zanussi ZWX1605 error codes

    I had checked the brushes they were ok, had a second hand motor so tried that and all ok now thanks for the help

    Bernie

    October 2, 2009 at 5:21 pm in reply to: Zanussi ZWX1605 error codes #298513
    Bernie
    Participant

    Re: Zanussi ZWX1605 error codes

    Many thanks for the info Brian

    Bernie

    September 29, 2009 at 6:39 pm in reply to: Candy Tumbledryer belt fitting #298227
    Bernie
    Participant

    Re: Candy Tumbledryer belt fitting

    To fit a belt involves a complete strip down Drum out I have not found any other way.

    Bernie

    September 29, 2009 at 6:18 pm in reply to: Beko WMA510 wash led lights on spin #298241
    Bernie
    Participant

    Re: Beko WMA510 wash led lights on spin

    Thanks Galway but that was one of my first thoughts but alas no.

    Bernie

    September 29, 2009 at 5:01 pm in reply to: Beko WMA510 wash led lights on spin #298239
    Bernie
    Participant

    Re: Beko WMA510 wash led lights on spin

    There was washing in it but I took it out just incase it was oob, but it was still the same.
    Thank TheSpinDoctor for the reply

    Bernie

    September 24, 2009 at 6:52 pm in reply to: Hoover HSWD166-80 Motor plug burnt out #297654
    Bernie
    Participant

    Re: Hoover HSWD166-80 Motor plug burnt out

    Thanks to both of you for the info will have a look.

    Bernie

    September 22, 2009 at 7:45 pm in reply to: Hoover HSWD166-80 Motor plug burnt out #297651
    Bernie
    Participant

    Re: Hoover HSWD166-80 Motor plug burnt out

    Thanks for the wiring diagram Martin. I have wired it correctly.

    Do you think that the module/PCB will need changing as it spins on wash?


    Bernie

    September 1, 2009 at 7:38 pm in reply to: Whirlpool AWM8123 door locks and that it is. #296024
    Bernie
    Participant

    Re: Whirlpool AWM8123 door locks and that it is.

    I’ll look into that,
    thanks for the tip jackster

    July 30, 2009 at 10:53 am in reply to: Zanussie ZWX1605W stops during wash and rinses #293418
    Bernie
    Participant

    Re: Zanussie ZWX1605W stops during wash and rinses

    I had tested machine for low insulation but that was ok

    have just put machine through the test program again the only lights that we flashing were the start/pause and end lights this is what I got the other time and I thought that it had finished the test, is that a fault code?

    The one thing that it has done a couple of times is it has spun on wash.

    Bernie

    July 29, 2009 at 11:24 am in reply to: Bosch 1200 washing machine softener nightmare #293353
    Bernie
    Participant

    Re: Bosch 1200 washing machine softener nightmare

    I am with SWERV on this one. I keep replacement top on van

    June 17, 2009 at 3:28 pm in reply to: Indesit WIA111(UK) Door lock light keeps flashing #289387
    Bernie
    Participant

    Re: Indesit WIA111(UK) Door lock light keeps flashing

    Thanks to you all for the info
    Bernie

  • Author
    Posts
Viewing 15 posts - 196 through 210 (of 289 total)
1 2 3 … 13 14 15 … 18 19 20