Bernie

Forum Replies Created

Viewing 15 posts - 181 through 195 (of 289 total)
  • Author
    Posts
  • in reply to: Hotpoint WMM75A No motor action #306284
    Bernie
    Participant

    Re: Hotpoint WMM75A No motor action

    Mike you got this one right, both wires to the taco were broken at the taco end.

    Thanks

    in reply to: Hotpoint AQXXD169PMUK F8 #309104
    Bernie
    Participant

    Re: Hotpoint AQXXD169PMUK F8

    The fault turned out to be a bad connection on the plug-in connecters to the main PCB, I had squeezed the small ones but it was not until I got a needle and eased each one out a bit that it cured it.

    I did first send the board to EMW who did not find a fault.

    Bernie

    in reply to: Hotpoint dryer CTD80 wiring diagram #310345
    Bernie
    Participant

    Re: Hotpoint dryer CTD80 wiring diagram

    Thanks for that Jim

    in reply to: Hotpoint dryer CTD80 wiring diagram #310343
    Bernie
    Participant

    Re: Hotpoint dryer CTD80 wiring diagram

    I haven’t been back to this yet going on Tuesday, I have just got a new thermostat kit (10703608) which has one-shot cut out, a cycling thermostat and an NTC, should I not get some sort of reading across this as both the one in the machine and the new one are open circuit

    Looking at the wiring diagram it shows the NTC as closed circuit.

    Bernie

    in reply to: Hotpoint dryer CTD80 wiring diagram #310342
    Bernie
    Participant

    Re: Hotpoint dryer CTD80 wiring diagram

    Thanks to both of you and a second thanks to A1 for the email

    Very much appreciated

    Bernie

    in reply to: creda t/d 37648 #310320
    Bernie
    Participant

    Re: creda t/d 37648

    Its not a red button but a red spot on the cut-out which is the 110 deg on the left, the other one could be a purple spot 85 deg on the right
    Hope this helps
    Bernie

    in reply to: Hotpoint dryer CTD80 wiring diagram #310339
    Bernie
    Participant

    Re: Hotpoint dryer CTD80 wiring diagram

    Thanks for that RickT

    in reply to: Bosch Dishwasher SGS43T62GB/73 check water led #310228
    Bernie
    Participant

    Re: Bosch Dishwasher SGS43T62GB/73 check water led

    Very Many Thanks to you nomadPaul

    Bernie

    in reply to: Hotpoint WF541G Lights 1&3 flashing F10 #308346
    Bernie
    Participant

    Re: Hotpoint WF541G Lights 1&3 flashing F10

    Thanks for that helo_75 as you say it’s worth a try.

    I went to a 14 month old Hoover last week, sealed tank pressure pot chamber is now part of that too.


    Thanks again
    Bernie

    in reply to: Bosch Dishwasher SHV55M03GB Water Softener Change #307485
    Bernie
    Participant

    Re: Bosch Dishwasher SHV55M03GB Water Softener Change

    It’s leaking from it at the front you can see the water trickling out where the top join is
    There are bubbles coming up the fill chamber that connects to the softener, so there had to be a hole in the softener
    The base had filled with water and activated the float switch

    Bernie

    in reply to: Bosch Dishwasher SHV55M03GB Water Softener Change #307483
    Bernie
    Participant

    Re: Bosch Dishwasher SHV55M03GB Water Softener Change

    Thank you for that Lee it will be most usefull

    Bernie

    in reply to: Ariston A1437 top two option leds flash #307481
    Bernie
    Participant

    Re: Ariston A1437 top two option leds flash

    Thanks you very much to you all for the info. A little light reading over the new year I think.

    Bernie

    in reply to: Hotpoint WMM75A No motor action #306283
    Bernie
    Participant

    Re: Hotpoint WMM75A No motor action

    Thanks for the replies and no I had not checked the taco.

    Thanks again
    Bernie

    in reply to: Dishwasher Tablets Article #305457
    Bernie
    Participant

    Re: Dishwasher Tablets Article

    Thats the one Thanks traceukw1 and to you to Martin

    Bernie

    in reply to: Dishwasher Tablets Article #305454
    Bernie
    Participant

    Re: Dishwasher Tablets Article

    Sorry Martin but that’s not it.
    I believe its title was:-
    The Good, the Bad, and the Downright Ugly Tablet

    Thanks Bernie

Viewing 15 posts - 181 through 195 (of 289 total)