[Bernie]

Re: Known Test Procedures

Whirlpool 6th sense Whirlpool condenser Dryer AWZ 8477 all the red lights flashing – “empty water bottle” “clean the filter” and “clean the heat exchanger”

Turned it to 6 o clock press start 3 times turn clockwise 1 click and press start 3 times, it is now reset

Bernie

[Bernie]

Re: Servis M3011A program sticks

Steve thanks for the reply

[Bernie]

Re: AEG 16850 PNC 91460530903 still very wet after drying

As I said in my post, I checked the new valve had the same colour restrictor as the old one, and it does. Do not know what else I can do regarding that.
I did wonder about the pump although it appears to work ok but it might be as you say martin Clapped out. I will have a look at both possibilities when I go back
Thanks to you both for your replies
Bernie

[Bernie]

Re: AEG 16850 PNC 91460530903 still very wet after drying

Seamy thanks for your reply.
I have checked the fan impellor all clean and appears to be running ok will have a look at the belt. It does get hot will check insulation as I said condenser all clear, will look at you other suggestions
thanks again
Bernie

[Bernie]

Re: Whirlpool AWZ8477 Condenser dryer just warm

Thanks for the quick reply Martin is that a common fault?

You say it is located in the front duct is it easy to get to on this machine?

Thanks again
Bernie

[Bernie]

Re: Whirlpool TD AWZ 8477 Not Drying

I have been told by another engineer that it might be the dryness module the heater relays in there fail.

It is the small pcb on the right hand side at the top.

Could anybody confirm this?

Bernie

[Bernie]

Re: Hoover Tumble Dryer VHC180-80 Not Drying

Thanks for the very quick reply

I have just looked on Connections website and there is a pdf for that modle but they do not list a part number for it, would you know it?

Thanks again
Bernie

[Bernie]

Re: Bosch WET2820GB/01 Changed motor end frame

Thank you for all your suggestions, but it was a faulty part.
I fitted new brushes to the old motor end frame(yes it can be done)and it all worked as normal.

Thanks again
Bernie

[Bernie]

Re: Bosch WET2820GB/01 Changed motor end frame

Found the tacho in the end frame, new one tests the same as old one. Other than continuity testing is there anything else I can do?

Thanks
Bernie

[Bernie]

Re: Bosch WET2820GB/01 Changed motor end frame

Yes Martin the part number was 496876
I was wondering about the tacho, where is it on these?

Bernie

[Bernie]

Re: Indesit IWB71250 (UK) No Fill

Just been back heater is ok – 31ohm, Insulation 999 meg ohms
Am I now looking at a replacement board?
Any other suggestions please
Bernie

[Bernie]

Re: Indesit IWB71250 (UK) No Fill

Thanks Martin
Will give it a go
Bernie

[Bernie]

Re: Indesit IWB71250 (UK) No Fill

Thanks for the reply Martin
I did not test it!
Bernie

[Bernie]

Re: Hoover OPH616/2-80 prog locked up

I tried holding the start button & turning the dial, that did not work until as you say mental twiddling the dial whilst holding the start button that unlocked it. I selected spin and it spun but when I tried to cancel it, it locked up again. So I thought I would clean the program selector, only it is soldered to the board and no way to get into it. I have some Amberlube contact cleaning lubrication so I gave it a spray and again mental twiddled the dial this worked.
Thanks for your help and suggestions
Bernie

[Bernie]

Re: Hoover OPH616/2-80 prog locked up

Thanks for the quick reply, will try what you have suggested

The price for the Fascia control module from Connections is £117.80 + VAT with a SRP of £207.88 not that cheep.

Bernie

[Author]

Posts