[Bernie]

Re: Indesit Tumble dryer ISL70C (UK)

Thanks iadom

Bernie

[Bernie]

Re: Indesit Tumble dryer ISL70C (UK)

I have just had another look at the photo of the heater on Connections website and it shows the cutout (white spot) wired in line with another cutout/stat and that the thermistor is now different white and not black (part no. 1702791)
So the correct part number for the heater is most properly be: – C00145747

So thanks to all of you who looked

Bernie

[Bernie]

Re: Sarena SW202 Washer Dryer

Thanks for the part number Andy, how did you find it? It says it’s for a Baumatic. Is it a Fagor? If so would you know what the model might be?

There has been a large building project and I would guess that the builder has put one of these in each flat/house (about 100) so it would be an advantage to me if I knew what it is.

Once again Thanks

Bernie

[Bernie]

Re: Sarena SW202 Washer Dryer

Sorry PGS but do not know JTM did a serch came up with :-
http://www.jtmservice.co.uk
JTM SERVICE LIMITED
6 MILESTONE COURT
STANNINGLEY
LEEDS LS28 6HE

Is this them? Could not find anything to do with Sarena on there website

[Bernie]

Re: Bosch WAE Washin Machine error codes

Sorry but have posted this in the wrong forum, should be in Trade Technical Enquiries

[Bernie]

Re: Crusader (Hotpoint) Tumble Dryer 31439 Front Pads Suppor

Thanks for the part number Jim sorry about model number.
Special order from connections, seeing that the belt, bearing pads and Drum Shaft Kit also need replacing does make it expensive.

Thanks again
Bernie

[Bernie]

Re: Crusader (Hotpoint) Tumble Dryer 31439 Front Pads Suppor

Thanks for the info boselecta
But it’s the pads support part number that I need.

[Bernie]

Re: Whirlpool D/W ADG7340 not washing

Thanks to you all for your suggestions, will be going back next week, will post what I find.
Thanks again

Bernie

[Bernie]

Re: Hoover HC6 160E , No Pump ?

I don’t know if it’s any help but I had one that I change the pump all ok.
Then about a week later got another call not pumping, new pump had blown pump triac sent board off to EMW for repair fitted it back wouldn’t pump, spoke to Tony at EMW was told these Hoovers with the extra two wires on timer have a digital module and he can’t fix them.
What I am trying to say is it the correct board?
Bernie

[Bernie]

Re: ZANUSSI EW1200

Has it got the timer 513316, had two of these last week doing just the same. Got replacement timers from EMW

Bernie

[Bernie]

Re: Hoover HP13 wire to variable spin switch

Very much appreciated Martin

Thanks Bernie

[Bernie]

Re: Tricty Bendix Washerdryer WDR1040W No Spin

Thanks Simon
Never had this fault befor

Bernie

[Bernie]

Re: Diplomat ADP8322 D/W it sounds like its washing

The problem continues. Now starts to fill for about 15/20 seconds then the start LED flash 7 times “Flow Meter Failure” Is it the Flow meter or is it the PCB?
Have tested flow meter it has continuity and it turns when it starts to fill, cleaned contacts also checked wires from flow meter to PCB continuity there too.

I did have a look at the sieve cover, I see what you mean about the plastic lugs but they are ok.
I guess if these break then the feed for the top spray arm will lift out of its socket and pressure will be lost.

[Bernie]

Re: Diplomat ADP8322 D/W it sounds like its washing

Thanks for the reply whiskeyjack6058, do you know the part number?
I have fitted a moter about 4 days ago.

[Bernie]

Re: Indesit DW IDL530UK2 4nd LED from left flashing

Will order a thermistor and give that a try.

The only part I can see on Partfinder is T/STAT SAFETY 78C NC part No. C00041086 is that correct, if not would you know part number?

Did find on another INDESIT IDL530 post about a module with ntc attached part No.C00143209 is that it?

Thanks for all the help and info.

[Author]

Posts