bubs

Forum Replies Created

Viewing 15 posts - 61 through 75 (of 193 total)
1 2 3 4 5 6 … 11 12 13
  • Author
    Posts
  • February 28, 2009 at 5:41 pm in reply to: New Bosch dishwasher heat pump #278704
    bubs
    Participant

    Re: New Bosch dishwasher heat pump

    Thanks for the reply’s, interesting.
    I did look a bit of an idiot trying to find the element 😳
    Will get them to phone BSH

    February 11, 2009 at 8:32 pm in reply to: Bosch Dishwasher overfilling #276950
    bubs
    Participant

    Re: Bosch Dishwasher overfilling

    Just to clarify, i assume it’s not getting a signal from the microswitch to shut the valve down.

    February 11, 2009 at 8:30 pm in reply to: Bosch Dishwasher overfilling #276949
    bubs
    Participant

    Re: Bosch Dishwasher overfilling

    Have been able to cure this twice by just re-seating the pcb connectors.
    Worth a try.
    Graeme

    February 11, 2009 at 8:19 pm in reply to: Bosch conderser dryers #276900
    bubs
    Participant

    Re: Bosch conderser dryers

    Sorry Martin it’s WTL6500GB/01

    Have spoken to customer and it flashed the container full light on the first try after 15min so cannot have had water in chamber or a stuck float.
    Cheers
    Graeme

    November 6, 2008 at 9:48 pm in reply to: Stoves hob 600cth error 56 #267076
    bubs
    Participant

    Re: Stoves hob 600cth error 56

    Thanks for confirming this charlie.
    Going to be expensive.
    Graeme

    October 14, 2008 at 8:28 am in reply to: hotpoint wma52 motor #265083
    bubs
    Participant

    Re: hotpoint wma52 motor

    Thanks Martin,
    Now I am a little confused (as normal).

    My Hotpoint friend has given me the part no 1604572(c00202516) based on the serial no so i assume this is correct.

    Your site is selling a 160411 listed as fitting a wma52, which is cheaper and in stock at Connect. Just wondered what the difference was an if you can fit either.

    Thanks again
    Graeme

    September 27, 2008 at 11:05 pm in reply to: Whirlpool dishwasher cw 446 #263403
    bubs
    Participant

    Re: Whirlpool dishwasher cw 446

    Hi,

    Can’t find this model, but if it’s got a level switch on the r/h side of the sump it could be stuck or faulty. Machine will try to pump until switch drops out.

    Cheers
    Graeme

    July 18, 2008 at 9:17 pm in reply to: miele dishwasher G7859 F26 #257927
    bubs
    Participant

    Re: miele dishwasher G7859 F26

    Thanks, Graeme

    July 8, 2008 at 9:33 pm in reply to: Beko WMA665W not washing #256198
    bubs
    Participant

    Re: Beko WMA665W not washing

    Just an update, went back to check tacho, all looked and metered fine. Had a good look a pcb, again nothing obvious.
    Tested on wash and then it all worked fine, could not fault. On Test!!
    Graeme

    July 8, 2008 at 9:24 pm in reply to: AEG A3193-6GA (928341122) Fitting evap thermistor #257067
    bubs
    Participant

    Re: AEG A3193-6GA (928341122) Fitting evap thermistor

    Thanks, done yesterday. Found it difficult to split the lower tray to feed in the front sensor. One of those take your time jobs.
    Thanks
    Graeme

    June 29, 2008 at 10:15 pm in reply to: Beko WMA665W not washing #256196
    bubs
    Participant

    Re: Beko WMA665W not washing

    Thanks, will go back and have another look.

    It puzzles me why there is no jump in speed when you try a spin prog, distributes fine. I an still learning Beko stuff…

    Graeme

    April 10, 2008 at 1:04 pm in reply to: Frigidaire CP1450 Grill Element #248727
    bubs
    Participant

    Re: Frigidaire CP1450 Grill Element

    Thanks Mr B

    April 10, 2008 at 12:20 pm in reply to: Frigidaire CP1450 Grill Element #248725
    bubs
    Participant

    Re: Frigidaire CP1450 Grill Element

    It’s coming up obs in Connections and one other internet supplier, have you a part no please?
    Cheers

    March 27, 2008 at 12:45 am in reply to: candy AQUA 1000T-80 module pcb #246913
    bubs
    Participant

    Re: candy AQUA 1000T-80 module pcb

    The Hoover Magic Box, sounds sounds fantastic !!
    Thanks again.

    March 27, 2008 at 12:31 am in reply to: candy AQUA 1000T-80 module pcb #246911
    bubs
    Participant

    Re: candy AQUA 1000T-80 module pcb

    Thanks lerch, sorry, not too sure what i need here.
    Is it both numbers or is this an option to order programmed / blank control boards?
    Graeme

  • Author
    Posts
Viewing 15 posts - 61 through 75 (of 193 total)
1 2 3 4 5 6 … 11 12 13