[bubs]

Re: zanussi No Frost ZK87/34EF no go

Thanks, have done so.

The compressor is not being started at all.
It’s a complicated thing compared to the common
VT9 + defrost timer models.

Cheers
Graeme

[bubs]

Re: hotpoint TDC62G killing toc’s…

Hi,
had one recall due to a faulty motor cap.
Graeme

[bubs]

Re: Funny Customer Names !

Mrs Sex, I didn’t say a word.

Graeme

[bubs]

Re: candy ccff26/13 not defrosting

Thanks Bob,
as you can tell i don’t go out on much candy frost-free 😳
This is a neighbour who has no space for anything other than onother candy.
Is the defrost timed or thermistor controlled?
May give you a call bob if no easy answer.
Cheers
Graeme

[bubs]

Re: Creda W200FW won’t work on “D”

Hi chaps,
just a thought but 2 of my customers have put the selector switch 180 degrees out as some are all white. Its not stop/change prog on the other side of D?
Cheers
Graeme

[bubs]

Re: zanussi WDJ1257W E40 not door lock

Cheers Steve for you advice

I will have a good look over it.

It’s a bit embarasing, when you get a hotpoint wma not locking due to the neutral missing you know 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} the pcb’s blown.

now if this lock doesn’t fix the E40 the odds are a bit less, i have a 50{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} success rate so far fitting the pcb, will have to carry a few “workers” on the van.

Anyone else having more success?

Thanks
Graeme

[bubs]

Re: Ariston Dishwasher AFA350X

Hi,
Had a very similar fault, not filling, was the heater.
Any strange faults on this range its worth checking first as it aborts the programme during fill and outputs a no fill fault code.
Cheers
Graeme

[bubs]

Re: miele G7762 salt light on

Thanks guys,
Will have a look this week when my back repairs itself 😯

Yes it’s in a care home, fixed a few faults before but not too sure how the salt light works. I know there is a seperate proramme to refill salt. There is zero chance of them having any info, all i get is “over there” sometime i fix the wrong fault!
Cheers
Graeme

[bubs]

Re: Hotpoint BF71

Hi, if you search BF71 there are a few previous threads.

Assuming you reset the programme and no water in base;
If the pump works ok via the base float I would have to look a module next. Have a good look at all the edge connectors and solder joints.

Cheers
Graeme

[bubs]

Re: Diplomat ADP8234 control pcb

Hi Dave,
put this into Connect and it outputs a contol panel at £16.
could you double-check this please 🙂
sorry to be a pain in the 😳
Graeme

[bubs]

Re: Bosch E14 fault WVT13240GB/01

Thanks boro & Tim,
have ordered the ntc.

Graeme 🙂

[bubs]

Re: Bosch E14 fault WVT13240GB/01

Thanks Boro,
Going tomorrow, I think they said it errors on wash / rinse; would a dryer fault show during wash?
Cheers
Graeme

[bubs]

Re: Zanussi Dishwasher Mod DE 6850

Hi, did you test the heater from the plug?
Sorry if its too silly an idea but it’s tempting to clamp the leads on the heater direct on these elements, done it myself.
Graeme

[bubs]

Re: whirlpool ADP4501WH error

Cheers Chris, Have ordered the pcb 😀

[bubs]

Re: AEG F86070VI dishwasher 10 error

boro wrote:

Yeah drop Carvalho, and Geremi is no right back 😆

As for the d/w aint got a clue mate.

Very true 🙂 Why do your lot only turn up every 4 weeks?

Back to the dishwasher, checked and raised the air-trap today; still have the save fault. It errors after about 1/2 hour, small amount of water in the sump so probably filling or draining. Every time I try a fill or drain it works fine. May have to give up on this unless any further suggestions? (Not from Boro!)

Cheers
Graeme

[Author]

Posts