[bubs]

Re: indesit Wi 335uk

Hi,
It’s a bit unlucky for the pcb to go the next day, maybe the pump connection has come loose as you had it apart; Not too sure if it stops fill on the indes*** but I have been caught out by this before.

Graeme

[bubs]

Re: AEG F86070VI dishwasher 10 error

Thanks for the file Chris 😀

The rubber air trap may need tying-up to stop water sitting in the bottom, if anyone else has the same problem.

Graeme

[bubs]

Re: Bosch d/w heater failures

I can remember thinking “easy to change the heater” as i looked with the side off 😆 Only 3 in the last 6 months, none before.

Graeme

[bubs]

Re: Hotpoint dishwasher

Hi,
Heater faults (Inc earth leaks) may cause all sorts of strange faults on this range, had one last week not filling. A Merloni engineer told me any slight doubt’s they are fitting new heaters.

Cheers
Graeme

[bubs]

Re: chanelle falling apart

Penguin45 wrote:Chenille………

………Barc 1 🙂

Thanks penguin, please someone add a spiel cheeker.

[bubs]

Re: chanelle falling apart

My wife tells me it’s a wool mix; if you sat in a lab for 10 years it would be impossible to invent a better WM blocker-upper!
Wilf, i have to agree on the feathers; Had a nasty one to clear a while back, it was the smell that got me, two pillows full.

Graeme

[bubs]

Re: Hygena APL3320 fan element

Thanks again dave,
looked in Maplins today for a tool, I will check RS 🙂

[bubs]

Re: Tricity-Bendix Cooker fan moter screws

Cheers aqua,
Nice to know they do move, I will put my drill away 🙂
Graeme

[bubs]

Re: miele washers & tumbles

I have been driven mad by scale in the filters, you clean them and can’t re-seal; have to carry a new filter and housing, perhaps not a problem in your area.
The older dryers blow relays on the PCB’s a lot (no motor action, no reverse) also check any protection fuses first. The fan motors can get noisy, rubbish in the fan, broken fan, fan motor bearing moving in the case.

Cheers Graeme

[bubs]

Re: Hotpoint DWF34

Think it’s a Bosch, had a couple of modules causing no fill; One obviously burnt on the connection block, one not.

Graeme

[bubs]

Re: Known Error Codes

Hotpoint BF72 Dishwasher (made by SMEG)

E1 Water in base

Other error codes are listed in the manual, E1 is missing.

Graeme

[bubs]

Re: Hopoint W/D 64 Dryer TOC

Good point johnny,

Fixed a drain fault on this WD and the customer said “dryer gets too hot”, I thought how can you tell? The loom had shorted againt the case where the cable tie is, it was turning the dryer heaters on all the time. Good old neutral switching, probably not quite enough juice to blow the fuse.

Graeme

[bubs]

Re: Hotpoint WF000

Had a chat with a Hotpoint agent last week. He had a “faulty on delivery” rate of aout 1{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} pre Merloni elctronics, now up around 10{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} . Starting to sell Bosch…….. 😉

[bubs]

Re: Qualtex Increase Staff

Hi,
I have worked in a shop using Stocklink; the parts came via a local distributor. Is the new system going to work the same way?
The people who have the qualtex software already; are you distributors?

Regards
Graeme

[bubs]

Re: bernstein 01-800270 DW overfills

Thanks, will order a presure switch.
Graeme

[Author]

Posts