Criscold

Forum Replies Created

Viewing 15 posts - 241 through 255 (of 816 total)
1 2 3 … 16 17 18 … 53 54 55
  • Author
    Posts
  • March 26, 2013 at 2:59 pm in reply to: Beko WMA767s drum paddle replacement #392746
    Criscold
    Participant

    Re: Beko WMA767s drum paddle replacement

    Looks like a drum strip down job but I could be wrong on this

    March 20, 2013 at 9:14 am in reply to: AEG Dishwasher #392416
    Criscold
    Participant

    Re: AEG Dishwasher

    Error 50 Motor triac short-circuited poss Circuit Board but req PNC to make sure this is correct

    Colin

    March 12, 2013 at 4:10 pm in reply to: Belling 930 Cooker Door Hinges Obsolete – Any Alternatives? #391874
    Criscold
    Participant

    Re: Belling 930 Cooker Door Hinges Obsolete – Any Alternativ

    I have a new pair sitting on the shelf that I ordered for a customer that cancelled the repair.

    Colin

    March 7, 2013 at 8:51 pm in reply to: AEG S75358 KG3 sensor part numbers #391719
    Criscold
    Participant

    Re: AEG S75358 KG3 sensor part numbers

    Do you mean the 2 thermal cutouts pt no. 2426484032

    February 24, 2013 at 12:34 pm in reply to: white knight tumble dryer (large vented ) #390820
    Criscold
    Participant

    Re: white knight tumble dryer (large vented )

    You could check on thier site here http://www.whiteknightrange.co.uk/white … ad-SM.html

    Colin

    February 20, 2013 at 6:59 pm in reply to: lamona hja8630 (beko) #390540
    Criscold
    Participant

    Re: lamona hja8630 (beko)

    Probably display card pt 1891520300 I normally change both this and module as the parts for these a cheap

    Colin

    February 19, 2013 at 11:00 am in reply to: Indesit iwde12uk ,no power to pump #390465
    Criscold
    Participant

    Re: Indesit iwde12uk ,no power to pump

    Have you checked thermistor on dryer duct and heater, for some reason when these become faulty it sometimes causes the pump not to run. Earth fault or OC.

    February 16, 2013 at 6:28 pm in reply to: Hotpoint dwf70 #390330
    Criscold
    Participant

    Re: Hotpoint dwf70

    The manual states that – Machines with a turbidity sensor. If the connector is damp or connections damaged,
    A01 will display

    Colin

    February 12, 2013 at 10:40 pm in reply to: zanussi WDS1183W 91463451501 #390055
    Criscold
    Participant

    Re: zanussi WDS1183W 91463451501

    This may help

    Colin

    February 6, 2013 at 8:17 pm in reply to: Leisure HJA6100 Diagnostics and any other Info Please #389555
    Criscold
    Participant

    Re: Leisure HJA6100 Diagnostics and any other Info Please

    If you let me have your email I can send you some info in the morning

    Colin

    January 17, 2013 at 1:08 pm in reply to: Hotpoint WDL5490 not draining #388102
    Criscold
    Participant

    Re: Hotpoint WDL5490 not draining

    Have you checked Dryer & Heater NTC for insulation faults or Poss open circuit as this can cause no pump fault

    December 13, 2012 at 6:50 pm in reply to: Indesit wixl 143 #386298
    Criscold
    Participant

    Re: Indesit wixl 143

    Found the following

    – Check motor not seized;
    – Check edge connector J9 has secure connections on
    module;
    – Remove edge connector J9 on module check wiring and
    contacts at position 1 and 2 on connector J9;
    – Check tacho generator windings and that there is an
    impedance value of between 115 and 170 ? on the wiring
    connector J9 between pins 1 and 2;

    Colin

    December 6, 2012 at 10:15 pm in reply to: Hotpoint BF1680 (D/W) #385962
    Criscold
    Participant

    Re: Hotpoint BF1680 (D/W)

    Heating Circuit – Heater or board

    Colin

    December 5, 2012 at 4:37 pm in reply to: zan zwf1000 sump hose #385889
    Criscold
    Participant

    Re: zan zwf1000 sump hose

    Hose listed as 4055059580

    Colin

    December 3, 2012 at 11:37 am in reply to: 11 flashes on hoover drier #385720
    Criscold
    Participant

    Re: 11 flashes on hoover drier

    Hard to say without model number but could be the Selector of the drying cycles is short circuited. Check the
    selector and the related wiring

  • Author
    Posts
Viewing 15 posts - 241 through 255 (of 816 total)
1 2 3 … 16 17 18 … 53 54 55