Criscold

Forum Replies Created

Viewing 15 posts - 406 through 420 (of 816 total)
1 2 3 … 27 28 29 … 53 54 55
  • Author
    Posts
  • April 10, 2012 at 7:42 am in reply to: Favorit 44080i AEG Dishwasher not drying the crockery #372981
    Criscold
    Participant

    Re: Favorit 44080i AEG Dishwasher not drying the crockery

    If the heater is faulty this machine would finish the cycle without heating, check the heater & board. PM you email if you req more info

    Colin

    April 6, 2012 at 9:57 am in reply to: bosch d/w sgs45e6gb/64 pump acess #372830
    Criscold
    Participant

    Re: bosch d/w sgs45e6gb/64 pump acess

    Yes it would, If nothing is blocking the inlet to the circ pump then I would go with the heater box as Martin says and I have done a few because of this fault. is the machine getting enough water ?

    March 29, 2012 at 5:04 pm in reply to: bkko wm5101w #372474
    Criscold
    Participant

    Re: bkko wm5101w

    Have you replaced the selector switch as well part No.2827190100 ?

    March 29, 2012 at 12:59 pm in reply to: beko wme7267w #372453
    Criscold
    Participant

    Re: beko wme7267w

    No F3 listed but E3 is heater or heater relay fault

    March 28, 2012 at 6:17 pm in reply to: HNWF7137-80 dryer element #372242
    Criscold
    Participant

    Re: HNWF7137-80 dryer element

    Lower Element listed as – 04820083

    March 27, 2012 at 3:23 pm in reply to: Hotpoint fdl 570 can’t program #372140
    Criscold
    Participant

    Re: Hotpoint fdl 570 can’t program

    It says in the manual -You MUST hold the Reader in place whilst programming is taking place.
    Is it possible that contacts aren’t making contact with module ?

    March 26, 2012 at 6:09 pm in reply to: SMEG Di612 #372137
    Criscold
    Participant

    Re: SMEG Di612

    You have mail

    March 25, 2012 at 9:48 pm in reply to: Aeg 75238-GA1 freezer #371341
    Criscold
    Participant

    Re: Aeg 75238-GA1 freezer

    Have you got the pnc + Serial Numbers on this unit

    Colin

    March 25, 2012 at 2:32 pm in reply to: Aeg 75238-GA1 freezer #371339
    Criscold
    Participant

    Re: Aeg 75238-GA1 freezer

    I don’t know but I do know that some of the heaters come with the stats wired in complete with the element.

    Colin

    March 25, 2012 at 10:09 am in reply to: Aeg 75238-GA1 freezer #371337
    Criscold
    Participant

    Re: Aeg 75238-GA1 freezer

    I don’t know if this answers the problem ?

    March 22, 2012 at 8:42 am in reply to: hotpoint ctd00 #371696
    Criscold
    Participant

    Re: hotpoint ctd00

    Probably the fan, broken blade, something caught in the fan sending it off balance or just worn loose on the shaft

    March 22, 2012 at 8:37 am in reply to: BEKO WM6143S HEATER WITH NTC. #371694
    Criscold
    Participant

    Re: BEKO WM6143S HEATER WITH NTC.

    The part you req is 2863701600

    Colin

    March 21, 2012 at 4:12 pm in reply to: beko american f/f fault #371504
    Criscold
    Participant

    Re: beko american f/f fault

    E8 = Ice sensor fault – sensor value is open or short circuit

    Colin

    March 20, 2012 at 10:26 am in reply to: wiring diagram ariston oven FB51ix #371394
    Criscold
    Participant

    Re: wiring diagram ariston oven FB51ix

    pm you email

    Colin

    March 19, 2012 at 5:57 pm in reply to: AEG 3085VI #371377
    Criscold
    Participant

    Re: AEG 3085VI

    Have you tried the diagnostic cycle to get error code on this machine ?

    Colin

  • Author
    Posts
Viewing 15 posts - 406 through 420 (of 816 total)
1 2 3 … 27 28 29 … 53 54 55