dave-m

Forum Replies Created

Viewing 15 posts - 106 through 120 (of 199 total)
  • Author
    Posts
  • in reply to: Indesit WD12x #366585
    dave-m
    Participant

    Re: Indesit WD12x

    That’s great stuff,.
    It’ll give me something to work with and may even save me a trip home to the workshop now!

    Cheers Jim.

    Dave

    in reply to: Indesit WD12x #366583
    dave-m
    Participant

    Re: Indesit WD12x

    Cheers Anyway

    I’ll megger it so and check the figures off a similar good one that I must have somewhere.

    D

    in reply to: SGV57T03GB/02 #366016
    dave-m
    Participant

    Re: SGV57T03GB/02

    Could be something caught in the wash motor impellor , giving poor circulating pressure

    I wish that was the case but a lot of the time it washes perfectly fine and then only at the end does it do the odd continuous wash pump thing

    dave

    in reply to: SGV57T03GB/02 #366014
    dave-m
    Participant

    Re: SGV57T03GB/02

    Thanks Martin.
    I’m thinking it has to be the board too, but i refuse to admit it without checking that I’ve not missed anything…

    cheers

    dave

    in reply to: Beko DRCS68 #364755
    dave-m
    Participant

    Re: Beko DRCS68

    I know i connected the heater plugs but tbh i never rechecked them after i put it all back together and noticed it wasn’t heating, it’s the only thing i didn’t recheck so hopefully thats it.
    I’ll let you know tmro.

    Ta
    Dave

    in reply to: De Dietrich halogen bulbs #364592
    dave-m
    Participant

    Re: De Dietrich halogen bulbs

    I’ll give it a go so,

    Cheers Bill

    in reply to: Hoover VHD924D #364588
    dave-m
    Participant

    Re: Hoover VHD924D

    Cheers for that mike, I saw how cheap they were so i ordered one anyway to try it.
    it sounds like they cause a few problems so hopefully it’ll do it.

    Dave

    in reply to: siemens SE25A831GB/17 no heat #364571
    dave-m
    Participant

    Re: siemens SE25A831GB/17 no heat

    did you check the board for a dry joint?

    D

    in reply to: Zanussi ZSF6128 #364254
    dave-m
    Participant

    Re: Zanussi ZSF6128

    Found the pump had been removed and not refitted properly, he swears he never took it out!, it was twisted back in at an angle and was leaking constantly.
    Refitted it correctly and checked all else and ran it with no problems.

    She phoned me later to say that it had the same problem “but at least its no longer giving electrical shocks”
    “what!” i said
    “oh yeah, did i not tell you that, after my hubby looked at it it was giving shocks, but its not now so thats good, back to the original problem”

    told her id look at it again tmro and start from the beginning.

    in reply to: SMV50C00GB/01 #362725
    dave-m
    Participant

    Re: SMV50C00GB/01

    He just got back to me to say it only works if he puts his weight against the door.
    He said his son is a kitchen fitter and he put it in so you were spot on.

    Cheers

    Dave

    in reply to: De Dietrich DOD338XU11 #361339
    dave-m
    Participant

    Re: De Dietrich DOD338XU11

    Thank bill, much appreciated.


    dave

    in reply to: Zanussi ZWD12270S #361318
    dave-m
    Participant

    Re: Zanussi ZWD12270S

    It’s Ed4.

    I had one a while ago and if I remember right the service manual (which, when I’m home, I can send you if you PM me your e-mail address) said it’s the drier board or washer board depending on a couple of tests.
    I rang a mate of mine, an engineer in zanussi, and he said it’s usually one of the two.

    The machine I looked at was 4 and a half years old so I rang zanussi for the customer and they sent out some one to repair it for call out fee only.

    However, Zanussi Dublin told me that if the machine was bought in Currys or someother outlet that doesn’t sell machines out of the Irish warehouse that it’s not covered by the Major parts warranty, so there!
    I gave her the s/n and this was ‘one of theirs’ so it wasn’t a problem.

    All that being said, I never rang the customer back to see how she got on, must do that today…


    Dave

    in reply to: Fisher & Paykel DS603H dishwasher error 1 #360320
    dave-m
    Participant

    Re: Fisher & Paykel DS603H dishwasher error 1

    I sent it yesterday, just checked, and it says it went but i’ll send it again now,

    Check your junk mail

    dave

    in reply to: Fisher & Paykel DS603H dishwasher error 1 #360318
    dave-m
    Participant

    Re: Fisher & Paykel DS603H dishwasher error 1

    e-mail?


    dave

    in reply to: bosch t/d pcb swap #360158
    dave-m
    Participant

    Re: bosch t/d pcb swap

    Good call Martin, I’ll try the latter first and even if they’re not the same I think I might then try the former as they want to throw it out anyway…
    Wish me luck…

    Cheers

    Dave

Viewing 15 posts - 106 through 120 (of 199 total)