[Electricmalc]

Re: Bosch WTE6920GB/01 FD8008 T/D Dead apart from display

Thanks Greg

If it is any help, I have just now, enabled my email on the forum.

Cheers

Malc

[Electricmalc]

Re: Bosch WFT2800GB/13 Washer dryer. Dryer question please

Learn something new everyday. 🙂

Thank you for replying

Malc

[Electricmalc]

Re: Bosch WFT2800GB/13 Washer dryer. Dryer question please

Thanks Martin

Yes blower fan working ok (I replaced it 18 months ago).
I did think on the same lines as you re testing with another element from van, but didn’t due to my other theory re no rise in temperature on ntc, might abort the supply to element. Suppose I could have tried that by warming the ntc. Oh well will x fingers when I go back with the element next week.
I will post here the result.

Malc

[Electricmalc]

Re: Hotpoint WD420

Flyman 😀
You have come up trumps on this, customer was also complaining that the machine “walks”.
I did not realise that the load is restricted to 1kg either.
I reckon the wash time, times out then on heating, rather than reaching the set temperature.

Thanks also to Iadom for your input on this.

Both much appreciated, thanks.

Malc

[Electricmalc]

Re: Swanmaid Dishwasher – an appeal

Martin

I can’t help find a Swanmaid Dishwasher.

I can remember repairing them. Used a perspex temporary door to check the water pattern from the jets etc. And they had a great big solenoid that pulled down the outlet hose for draining under gravity.

Life was a lot easier in them days.

I did an apprentiship as an electrician in 1964, 😳 can’t remember why we had to repair Swanmaids :rolls:

Malc

[Electricmalc]

Re: Belling Format 648HMSI part required

Thanks Chris
I appreciate you taking the time to find this out for me, one less problem to deal with, sometimes parts can be a real pain to source.

Malc

[Electricmalc]

Re: Zan defrost timer wiring

From wiring diagram on TDS shows the following for the sankyo timer

1 live
2 to defrost heaters
3 neutral
4 to compressor and fan

There are several ZX57/3SI but with different pnc numbers, the wiring looks the same.

Malc

[Electricmalc]

Re: Hotpoint top loader 9605 pump question.

Looks like I may well have a recall before the 12 months is out then.
Hadn’t realised that this had been discussed over a year ago. Thanks all.

Malc

[Electricmalc]

Re: Hotpoint top loader 9605 pump question.

There is a paper insert in the box that says not to use jubilee clips.

Thanks for all the replies.

Malc

[Electricmalc]

Re: Hotpoint top loader 9605 pump question.

Thanks Merv

[Electricmalc]

Re: Hotpoint top loader 9605 pump question.

Thanks for your thoughts Graham.
The picture of the genuine pump on connect, shows an aluminium pulley. The picture of the pattern pump, well the pulley is not easily seen as it is in shadow, Hmm

Malc

[Electricmalc]

Re: Nardi Dishwasher, all lights flashing

Thanks Chris, I had a feeling that it could be the switch on the door, will go see if that is the case.

Malc

[Electricmalc]

Re: Whirlpool AWM029 washing machime advice please

Thanks very much Bazza, another one for the big hole in the ground.

Malc

[Electricmalc]

Re: Hpt WD420 heater box modification 39 date code

Thanks Helo 75

Malc

[Electricmalc]

Re: Hpt WD420 heater box modification 39 date code

Thanks Jim 😀

All noted, will find out how much that will cost.

Cheers
Malc

[Author]

Posts