[electrofix]

Re: Washing machine advice

the miele will outlast the bosch do a google search on miele you will find the reveiws. They are quiet and dependable. there are very few manufacturers that design machine to last over 10 years but miele is one of them. 15 year old miele’s are common

went to a miele last week household has 5 adults machine 12 years old first fault brushes gone through wear and tear

look around there are other models of miele and sometimes they offer extended warrentys with them like

http://ao.com/product/WDA210-Miele-Wash … 29728.aspx

got a miele myself and i have the pick of anything

Dave

[electrofix]

Re: whirpool awz 510 e programs not working

out of ideas now assume it gets to rinse and wont pump out or spin.

have also assumed you have checked for blockages in outlet and sump hose etc and for a failing pump (have you checked to see if the pump coil is overheating some have cut outs ?)

Dave

when its empty does it spin then

[electrofix]

Re: Whirpool ADG 642 – pulsing issue

it does sound like a power supply problem which may be fixable but if you have to buy a new noe then yes i would be sitting down.

there is a firm that repairs some of these boards

http://www.qer.biz/

you could try asking

Dave

[electrofix]

Re: Whirpool ADG 642 – pulsing issue

still has all the hallmarks of the main control board being at fault

Dave

[electrofix]

Re: whirpool awz 510 e programs not working

so 50 degree wash

pump runs, then fills (all the way or just a bit?)
it then tumbles but does it heat ?

does sound a bit like a timer prob. have been looking for a picture of the panel but cant find one

dave

[electrofix]

Re: Whirpool ADG 642 – pulsing issue

sound like a power supply fault on the main control board

you say it takes a long time to do the cycle. if this is the fault its a miricle it even gets into the cycle

Dave

[electrofix]

Re: Hoover VT 816D22

first check the wire that goes between the panel and the main pcb. its very likely you have disturbed the connection one end or the other. also check there is power coming in. would not be the first time a customer was going to scrap a machine for a faulty socket

Dave

[electrofix]

Re: Diplomat dishwasher APD 8902

from what i can see this is a smeg built unit. finding the valve is easy its screwed onto the end of the water pipe from the tap. cant think how to remove it off hand but most dishwasher allow the sides to be removed for access or there may be a panel underneath you can get at it

Dave

[electrofix]

Re: Bosch WTA 3100 GB /07 FD7901 02197 – replacement door ca

go here

http://www.bosch-home.co.uk/store/spareparts/search

put in your Enr and you will find pictures that may help

a lot of doors are clipped together with the odd screw so should be straight forward

dave

[electrofix]

Re: whirpool awz 510 e programs not working

info is a bit confusing

in post you say it wont do any other programmes which sounds like it does some. if so which ?

if it wont go at all then my first look would be heater, brushes and door lock

Dave

[electrofix]

Re: Washing machine advice

from my point of veiw i would go for either

http://ao.com/product/WAE28461GB-Bosch- … 27063.aspx

or

http://ao.com/product/WDA100-Miele-Wash … 29725.aspx

the bosch machine is not the cheapest but as with most manufacturers they cut corners on cheaper machines
the miele is dearer but in a class of its own. miele units are the only machines where i need help to deliver them because of weight

hope it helps

Dave
both machines carry 2 years warrenty

[electrofix]

Re: Hoover VT 816D22

from what i can see the whole front board is not that expensive
part no 41035005
but
it depends on what you mean about wont power up

do you mean
A no light or power at all
B has light but wont start programme

if it A then this front panel is only a slave board and the is a link between the 2 boards. make sure the wire is secure at both ends
if it B then it could be just the front board if you have made a mess of the switch

Dave

[electrofix]

Re: AEG KM8403001 Microwave Combination Oven Help

dont know what you have tried but
http://www.aeg.co.uk/Page-Footer-Menu/A … ntact-AEG/

from this page either send a comment and they should ring you

or i would ring 03445 611 611

and take it from there

if you do get a support agent ask them for numbers they must know

Dave

[electrofix]

Re: Indesit IS70C thermostat

if the heater is glowing am I to assume you are running it with the back open. if so its normal it will it needs to be enclosed to work.
you problem must be down to air flow. check fan, filter, and especially condensor (make sure you can see right through it front to back)

Dave

[electrofix]

Re: Candy CDI 2012-80 built-in won’t stop draining.

a lot of dishwasher have a float in the base to detect leaks. if a leak is detected it starts the pump and it wont stop
not sure if yours has but it worth a look

Dave

[Author]

Posts