[electrofix]

Re: Miele G646SC Dishwasher

may not be a seperate drying heater but it will get hotter on the dry cycle

Dave

[electrofix]

Re: Hja8630 not drying

have you checked if it heats on final rinse ?

Dave

[electrofix]

Re: What’s the difference between an Eaton ec4684 timers?

not something thats easy to find out. the only place it may be listed is on the tech info from the manufacturer of the machine
you could email eaton and ask

Dave

[electrofix]

Re: What’s the difference between an Eaton ec4684 timers?

this help

http://www.ebay.co.uk/itm/Indesit-washi … 3f2397bf29

Dave

[electrofix]

Re: Bosch Logixx not filling very well

its unlikely to be internal hoses

check externel first

check feed hose not kinked or squashed
check tap and make sure there is a good feed of water getting to dishwasher by removing cold water hose and turn tap on while holding hose in a bucket

you need to eliminate the silly faults before you proceed

Dave

[electrofix]

Re: Amica d/w zwm 616w

ask site shop they are main supplier for amica

Dave

[electrofix]

Re: AEG Oven B4101-04-m

its only a basic diag i have but you welcome to it

send me your email add

Dave

[electrofix]

Re: Favorit 88070 error code 30: water inlet solenoid faul

you are right putting water solenoid before inlet hose means this hose is not pressurised so less likely to burst

one of the faults listed for i30 fault is short circuit triac controlling water solenoid on the pcb. that where i would look next

hope it helps

Dave

[electrofix]

Re: Lamona HJA 6740 Temperature Control

this is a maybe as i cant confirm

looks like you freezer may be made by stoves and from the websearches i have done

part number 082641500 maybe what you are after

maybe othe members can confirm but this sensor is used in both ovens and a wine cooler so it tick the right boxes

do a google search for your model but i would also email site shop to see if they can help

Dave

[electrofix]

Re: any body heard off gworks ltd

done a couple of jobs 4 them bit slow paying but not been left swinging so far

just done a cooker for them then had a emial to do a job in Rochdale so stopped that on it too far from liverpool

i charged them £45 to look at it then parts and lab from there

Dave

[electrofix]

Re: Indesit WIL 133 Washer

i would check the pump triac anyway also if house has no rcd have you checked for earth faults ? as most of the components neutral switch. trace pump wire to board and see if your multimeter gives you a reading across it

have you disconnected pump ( not sure if units senses it or not) and see if it will fill ?

this is one of those trial and error faults.

Dave

[electrofix]

Re: Zanussi WDJ1285 Tripping RCD in Fuse Box

difficult to know without someone checking it but

2 most likely things are heaters and motor

since this as a washer dryer first thin i would do is
1 unplug machine
2 take off lid
3 at the back of the tumble dryer section you will find the heater element connections. make a note where they go and disconnect them. then try machine and see if it trips

if it does not trip then you can tape up these wires and secure them and you have a washer but no tumble dryer

Dave

[electrofix]

Re: Indesit WIL 133 Washer

if you cancel the programme does the pump still run till the door unlocks ?

am thinking poss the triac that controls the pump is short circuit on the board

Dave

[electrofix]

Re: Relay on Hotpoint WF541 module

from looking at the print on the board this relay goes straight to the motor triac. it is likely the motor could be the source of a problem

to be certain you need to buzz the wirs through to see where they go

relay common connects to connector J9 term 3

normally closed goes to the motor traic

normally open goes to conn J9 term 7

not sure of the fault you have but this is a reversing situation, so if 1 relay sticks then you can get high currents flowing as the motor tried to run with a shorted aramture or field coil

Dave

[electrofix]

Re: Bosch tub change

with the heater disconnected the machine will take longer as it is thinks the heater is working. you will get no fault code but the timing will keep dropping where it will stick at 1 min

was the heater working ok when its connected ?

Dave

[Author]

Posts