Forum Replies Created
-
AuthorPosts
-
electrofix
ModeratorRe: Split Bosch tacho magnet. Motor p/n 142122
no probs m8 glad you got it sorted
Dave
electrofix
ModeratorRe: Dyson CR01 F11 Fault code
if it blows fuse then bridge rec is likely
take board out and check with multimeter
cheap repair but board is a bit of a pig to get out and in again
Dave
August 28, 2012 at 10:02 am in reply to: Whirlpool ADG9540 Exit pump on all the time and no water #379891electrofix
ModeratorRe: Whirlpool ADG9540 Exit pump on all the time and no water
most likely a blown triac in the programmer but you would have to strip timer and test for short circuit
Dave
electrofix
ModeratorRe: candy auto go482/2-80
not seen this but had plenty of wrong programme selected.
I would change 22 position switch first always a good bet and cheapDave
August 23, 2012 at 11:26 am in reply to: Whirlpool ADG9540 Exit pump on all the time and no water #379889electrofix
ModeratorRe: Whirlpool ADG9540 Exit pump on all the time and no water
is it coming up with a fault code
count flashes on start light
is float switch in base operating ok ?
Dave
electrofix
ModeratorRe: diplomat apm6855 fridge freezer
no unfortunatly
a lot of electronic controls switch neutral which means the connectors are always live
i would go with Samuri as my knowlege on friges is more limited
Dave
electrofix
ModeratorRe: diplomat apm6855 fridge freezer
its one of those jobs
a bit difficult to diagnose from afar
how did he test for power on the fan. if he did it with the door open then its not test as most of these fans only run with door closed
if the fan is running there is normally a motorised flap in the fridge that has to open. if it does not then could be flap , pcb , or thermostat
not to drag on further you need to look on this site for a local engineer with knowledge of these units. he will prob know common faults and will prob advise on the phone the most likely problems
Daveelectrofix
ModeratorRe: Bosch Exxcel 1400 Express Fault Code
its difficult to be certain due to this specific fault code no being listed
buti would check inside base of machine first some indications i have found information from other members that this machine has an anti-flood device and this fault code may be linked to it
take the back off and check for water flooding inside base
remove plug first !!
Dave
electrofix
ModeratorRe: bosch WTB 76556 GB/05 no heat
just changed relays a lot cheaper than the board
cant remeber if i got relay from farnell or radio spares but was easy to source and less then £10
Dave
August 18, 2012 at 5:16 pm in reply to: Miele Novotronic W970 – Intermittant “Check Inlet” light. #379654electrofix
ModeratorRe: Miele Novotronic W970 – Intermittant "Check Inlet" light
long shot
when it does it is it full of towels ie needs more water ?
Dave
August 18, 2012 at 5:10 pm in reply to: Miele Novotronic W970 – Intermittant “Check Inlet” light. #379653electrofix
ModeratorRe: Miele Novotronic W970 – Intermittant "Check Inlet" light
the problem with these type of faults is it does not happen every time
as all machine get old things perish and miele’s are not immune. my first thought would be inlet valves it may be getting enough water in but is it going in quick enough (i.e. is the valve not opening fully )dave
electrofix
ModeratorRe: Split Bosch tacho magnet. Motor p/n 142122
look at ebay item no
330766930710
Dave
electrofix
ModeratorRe: Fisher&Paykel Oven
electrofix wrote:only seen one fisher and paykel oven and it was a neff in disguise
Dave
mine was the blue inside one but it did use a bosch neff element so i assumed
Dave
electrofix
ModeratorRe: Split Bosch tacho magnet. Motor p/n 142122
best price i can find on new motor
europart £92 plus vat and carriage
not in stock though so you would have to check price is currentDave
electrofix
ModeratorRe: Split Bosch tacho magnet. Motor p/n 142122
only did one so cant quote on magnet size
magnet was on plastic frame that slides on shaft and the bearing goes on after it
Dave
-
AuthorPosts
