[electrofix]

Re: Bosch washing machine fault code WIS24140GB 07 fault cod

dont know with this range
on one range you set ptog to 6 0clock hold spin speed button and tunn prog 1 click clockwise then let go spin button turn off then on and try again but it may not work on this

have you tried all programmes ?

does the motor ever turn ?

does it stop about the time the motor should turn?

have you looked at pcb for bad solder joint ?

if you still stuck pm Nomad he seem to have bosch knowledge

Dave

[electrofix]

Re: Whirlpool ADP644BR dishwasher .

From what you are describing you are sayiny as the unit starts to fill the valve turns on and off in short bursts causing the leak due to lack of constant flow

if i have got it right my next step would be to investigate the programmer. From the pictures i would say it has a series capacitor power supply and these fail over time and cause this sort of fault.
see simple pcb repair tip for more info

trade-technical/simple-pcb-repair-tips-t51155.html

Dave

[electrofix]

Re: Bosch class 1xx leak problem

some machine you can tip but you have to be careful you dont get electrics wet
best way take a side off and mop it out

Dave

[electrofix]

Re: Bosch washing machine fault code WIS24140GB 07 fault cod

does this fault show on turn on or only when prog started?
( some bosch machines need resetting after fault or it wont clear )

does it run any progs ie rinses spin etc

if it does run how long before it fails ?

Dave

[electrofix]

Re: ball in pipe

as far as i know it stops the soap powder from ending up in the sump hose when it should be in with your washing

Dave

[electrofix]

Re: Hotpoint WMA74 Door Latch

try this

http://www.ebay.co.uk/itm/Hotpoint-Cred … 19cebdd530

£5 delivered

to fit
there are 6 screws in the door

undo top and bottom ones
undo 2 screws by the door handle

gently part door front and rear by handle and you can open it just enough to take out the handle as one unit and replace it

takes all of 5 mins very easy handle to fit

Dave

[electrofix]

Re: Belling Dishwasher IDW604

since belling is part of stoves most suppliers

check Qualtex they list 5 parts inc pcb, heater, doorlock etc

pcb is in stock

dave

[electrofix]

Re: Kenwood KDW60x10 unable to select prog

last time i had a prob like this it was the door switch

they are junk though. the electronic build quality is like japan in the 70’s

Dave

[electrofix]

Re: Hotpoint WMA74 Door Latch

easy change but you can still use machine

turn on machine
set programme but dont press start
close door
gently press door handle towards machine ( not the door the handle in the door )
whilst still holding press start and wait till door locks
now let go and wait till prog finishes
you may have to press door handle again to release

if you want to replace it it is an easy fix and you can get the spring only which is what breaks most of the time

part no C00097647

Dave

[electrofix]

Re: Bosch class 1xx leak problem

from what you described the base has flooded and the sound you are hearing is the water punp running to stop any further leaks
there are a number of things that can cause it

foaming due to exess or wrong detergent
leaks either through component failure, dirt on seals or even mice

you need to drain base and run it again after cleaning door seals etc and watch for water leakage in the base

Dave

[electrofix]

Re: Can you tell the age of Bosch washers by model name?

if you had stated the model some of us may have an idea but
if you get the full Enr number and serial no I am sure Bosch would be able to date it for you
look up bosch for your country through google

Dave

[electrofix]

Re: zanussi oven ZBF360X 949712292

bit difficult from diag but my guess is its

357 05 60-07 / 2 thermostat,NA 80/60

the only other stat listed is labelled

themostat set stirrup N.C 120/80 which i assume is the normally closed safety thermostat 357 05 62-01/1

Dave

[electrofix]

Re: Commercial glass washer

like this ?

http://www.ebay.co.uk/itm/Skivvy-glass- … 3a795eb6a8

as for glasswashers make sure you know the source of spares before you buy there a lot of oddball ones out there and most seem to be italian. my favourite is direct catering classic range very easy on spares and quite well built

Dave

[electrofix]

Re: White Knight dryer belt/bearings?

no probs m8

I only found it by accident

Dave

[electrofix]

Re: White Knight dryer belt/bearings?

try

http://www.whiteknightrange.co.uk/white … ad-SM.html

whiteknight publish service info online

Dave

[Author]

Posts