Forum Replies Created
-
Posts
-
Re: SGS53C02GB/15 Part No wonted
go here
http://www.bosch-home.co.uk/store/spareparts/search
go to bosch spares enter Enr and diag and spares parts info is there
Dave
Re: Electrolux website changed
its mad!
would not object to a yearly fee for access say £30 or so but but i have the same problem i would not spend enough and with the extra p&p i would have to pay for small orders it would be sillyDave
Re: miele s7580
if she has dropped it i would expect poss breaks in the pcb tracks as the components are very robust
with the thermo light on i would look for open circuits
you can buzz from plug to triac from both live and neutral with switch in on positon .
one way will be a dead short and the other will go through the motorhope it helps
Dave
Re: Problem with door spring
have you installed the outer door ?
integrated dishwasher doors are sprung to allow a decor front to be added and theses vary in weight
there is normally an adjustment but if you back it off too far the spring may fall off
check the instrution / instalation manual for more helpDave
Re: adg450/3 cuts out
yes look in simple pcb repairs above you will ee some of my posts on the subject and other members
dave
Re: Caple WDI2201
would be interested in tech info on these
have a long standing issue with tumble dryer i posted some time ago
Dave
Re: Bosch WVD24460GB/02
there are only 2 possibilties
brown black black or
brown black brownfrom memory i think its 100 ohm fusible resisitor
its a safety device to reduce the risk of board fire
Dave
Re: Bosch WFF2000 – motor problem
anything is possible
look for bad solder joints on board, blown motor triac ( the one on the heatsink and of course blown tracks
Dave
Re: Electrolux ZWF12070W
from what i can see looking at trech info a number of things spring to mind
1 the pump is fed permanently live ( eve if machine is switched off ) so if there is a neutral short pump will run all the time mavchine is plugged in
2 if machine is fitted with a leak protection system check float in base and switch for carrect operation
if pump start as soon as you switch machine at the panel then pump triac on pcb is suspect
am showing 2 varients of this machine and there may be more
prod code 91421610400 and 91452142600
if you let me know which one and give me you email will send you the info
Dave
Re: adg450/3 cuts out
first thing i would try is programmer power supply cap fault sound a bit like it
Dave
Re: Hygena APL 8124/1 Not Filling / Filling very slowly
its probably the inlet valve which is around £50 retail
but before you jump in and order check water supply its not the first time i have found a kink in a water pipe the works for a few years then stops the water
take water pipe off and make sure you have a good water flow to machine
Dave
Re: Componant ID……
leavemetogetonwithit wrote:Kind of strange for a resistor to go what is practically short circuit. I wonder if you got the number of bands right. There are sometimes 4 + the tolerance with certain types.
http://www.elexp.com/t_resist.htm
Mike
agree never known a resistor to go down in value only upDave
Re: HJA 8703
its a candy prob the selector switch there always going fitting one in about an hour to same machine
Dave
Re: Neff Fan Assisted Oven Tripping RCCB
Martin wrote:
Really? Is that wise? What amount of heat is required? And, without a test meter, how will I know if the problem has resolved itself?
which is why i used the word “may”
only the other week I cured an oven that was tripping that had been sat in a garage for 12 monthsgot elements out put them in another oven at 200 degrees for 2 hours
Dave
