[electrofix]

Re: Zanussi ZWD16581W

any time m8

got my tds running on a virtual cd using virtual cd v9
that means its loaded onto my hard drive as an iso file
also means i can install same disk on 3 computers with 1 disk.
using hard drive is faster access than cd and you cany scratch the cd

Dave

[electrofix]

Re: Zanussi ZWD16581W

check your email from your website sent you some reading material

Dave

[electrofix]

Re: Hotpoint WM64 Hinge Bearing Guide Screws Size/Type?

just make sure thay are not too long otherwise they will break through the door skin

Dave

[electrofix]

Re: Bosch SGS5342 GB/17 will not fill with water.

have you checked

1 you have water turned on and no kiks in pipe
2 solenoid water valve coil failure normally in a quiet room as it tries to fill you will hear a faint buzz from the valve. if no buzz dont assume its not getting power chack coil first but if no power coming from board look first for broken wires in the door

Dave

[electrofix]

Re: Hotpoint WM64 Hinge Bearing Guide Screws Size/Type?

i am assuming from your decription that the screws you have lost are the 2 screws that hold the 2 halves of the door together by the hinge securing the hinge bearings / pivots

screws are nothing special just small self tap screw. there
is another screw in the door frame that will be the same size use that as a guide

Dave

[electrofix]

Re: AEG Washer/dryer Dryer L16820 E10 Fault.

chance are then you will have an E12 fault E10 is displayed to the user

E12 Difficulty in water fill during drying (maximum
time 3 min. water fill in drying during the wash
load unrolling phase)

poss causes

Tap closed or water pressure too low; solenoid valve; pressure switch water circuit; pressure switches; wiring; main board

according to lux

Dave

[electrofix]

Re: Hotpoint EW 31 Oven – Low Temperature

you dont say a colour but the white handle should be
part no C00227259

check the thermostat prob in the oven is still clipped into place. if they come loose and get too close to the element it causes the same symptoms

Dave

[electrofix]

Re: samsung BF641 fb xeu pcb

resistor came with harness

overload at top rear of oven no wires on new harness so can connect
overload on fan housing n/c tests ok

Dave

[electrofix]

Re: rangemaster 5444

looking at the picture of the clock on connect it shows 2 small terms and 2 large ones

its got to be the 2 large ones but if you want to make sure take the pcb out and trace the tracks and they will go straight to the relay

also are you sure there is no an inline stat hidden anywhere that has blown. They do list a thermal cutout on connect

Dave

[electrofix]

Re: rangemaster 5444

if you can post a good picture of the clock printed circuit board showing components will try to hazard a guess

Dave

[electrofix]

Re: samsung BF641 fb xeu pcb

anyone got any tech info for this oven

got new board ,wiring harness * 2 plus top oven plate as per instructions on samsungs site.
top plate is no different from old one so did not fit that. all wiring colours had changed too me over 2 hours to trace all wires through but had to make an educated guess on the remaining.
got it to the point oven operates all ight and fans work in right places but no heat
am suspecting faulty thermistor but i dont know. has anyone got a resistance measurement for it. if i disconnect board knows its gone so i would assume resistance is not too high but is this a negative or positive ntc ie does resitance go up or down with rises in temp

Dave

[electrofix]

Re: rangemaster 5444

as with most timers look for the relays
and join those wires together

Dave

[electrofix]

Re: Why do some oven elements last longer than others

garn wrote:hi i installed a element on neff oven 11 months ago and It looks like It has Failed .
❓ why is it that some of these oven elements don’t last very long
Is down to genuine part or Paten part :con: :help:

Garn

had more problems with the neff horse shoe element than any other. used ELE2052 but these used you blow bottom right hand corner seemed to me they had bent elements too close.
Then tried ele2052ego only to watch it go bang while i was watching it
So its Gen from now on

Dave

[electrofix]

Re: Electrolux hood EFC60671x 942122181/00

checked lux info from 2008 lux disk
service manual is of no help and is too broad covers different models. no mention of electronics at all

have wiring diag which wont help your fault

so you have to hope someone has first hand knowledge. think it may be a new hood

Dave

[electrofix]

Re: Bosch WAA28161GB/02

cant find 02 model but 07 model belt part number

661153

useful link all bosch diag and part numbers

http://shop.bshappliancecare.com/

for some reason this site hates internet explorer so try another browser i use myie2

Dave

[Author]

Posts