Forum Replies Created
-
Posts
-
Re: AEG D5701-4-M Fan element permanently on
since this element is controlled by a module my first check would be the control relay on the power board ? short circuit
DaveRe: Hoover Optima 1400 A+ cycles deprogrammed?
if you get me the model number either i or some other kind soul will give you the part number
see label inside door
Dave
Re: Hoover Optima 1400 A+ cycles deprogrammed?
behind the knob you turn to programme the machine is a small switch. when they go faulty you get all the wrong programmes
its a cheap part and an easy fix
Dave
Re: AWCT10L – not take water in
long shot
had a few of theses machines where the customer switches iff at the socket before turning off the machine causing the computer to scramble
cure
press the off button on the machine till light goes out then turn on again to reset computerDave
Re: Maximum length of ducting?
seen water locked dryers on a few occasions
best one was a school where they had used 4″ soil pipe but had a dip in it so it filled up with water
condensing units dont work very well and wont stop all the moisure plus the fact you need to put ice in them to work properlyyou could use soil pipe to extend but make sure it has a fall to outside. dont forget in cold weather more condensation will form in the tubes and as stated keep it as short as poss to prevent problems
DaveRe: diplomat adp8501
cant remember what power supply theses older boards use but it sounds like a similar problem. would have to see a good picture of the component side of the board to make any guess
Dave
Re: whirlpool sm8 28115A not spinning 10kg commercial was
cant find model but
is this a top loader
if so see part number
481969018152
if this clutch is turning on spin but tub is free but wont spin up check following
look for contamination ie oil from gearbox on this clutch
if no oil change clutch
if you have oil change box as wellDave
Re: diplomat adp8501
since this is a whirlpool dishwasher this post may help
chris repaired the timer and unit is ok now
Dave
Re: john lewis jlwm1201
same fault code comes up if motor has an earth fault
ie wet or carbon dust
Dave
Re: john lewis jlwm1201
had done the same info criscold beat me to it
check for motor shorts to earth that can cause E51 faults
check obvious like brushes
if motor turns and stops check for tacho outputDave
Re: AEG lavamat turbo (L 14710-VIT) washer/dryer will not wa
just as another thought
this dryer element is 2 seperate elements. it is likely that only 1 element has failed you could connect them one at a time if you can get the element hot it might cure it
alternativly take out element and use a blowlamp or gas ring and get element hot ( or put in the oven for a few hours )
Dave
Re: AEG lavamat turbo (L 14710-VIT) washer/dryer will not wa
dryer heater part number 124 26 58-31/6
for price and avail email
the heater has an earth fault that upsets the electronics the only test you could do is to megger the heater
This sort of fault is not uncommon if you only use the dryer occasionally. it is good practice to run the dryer about once a fortnight for 20 mins or so to keep damp out of the element. if you get damp in the element and turn it on all this damp trys to exit at once causing an earth faultto remove element you have to split the machine case and the back comes away dont know how bad a job it is from there not done one
Dave
Re: AEG WASHER DRYER L12830 Fault code E20
without going into diagnostics you could have 1 of 4 faults
E21 poor draining
E22 Difficulty in water fill during drying or drying
condenser clogged (anti-boiling pressure switch closed on “FULL”)
E23 Defective triac for drain pump
E24 Malfunction in sensing circuit on triac for drain pump
can send you workshop manual if you let me have an emailDave
