[electrofix]

Re: dishwasher stopping intermittently

their is an anti-food device on that machine

if the base of the machine is full of water ( not where you put your dishes ) then there is a float that operates a switch which makes the drain pump start and it wont stop till the water is removed
it may be a serious fault or a simple as a blockage unless someone checks you will not know

Dave

[electrofix]

Re: AEG lavamat turbo (L 14710-VIT) washer/dryer will not wa

to get the part number i need the pnc number off the machine

open door and look at the label you are looking for a number that starts

9146012

has up to 11 digits in total

Dave

[electrofix]

Re: Model:APM8703/2 – filter plug leak

part are available but you have to make sure seal is in the right place and clean. sometimes 1 hair can make them leak
email the shop for spares

Dave

[electrofix]

Re: AEG lavamat turbo (L 14710-VIT) washer/dryer will not wa

turn power off
take lid off
heater box is on top front to back
you will see element connection at rear
note where they all go and there is just enough room to take them off. make sure they cant touch anything and run machine to check
if you want to fix it you need a new dryer element but you dont have to fit one if you dont use it

Dave

[electrofix]

Re: electrolux EOB 6630 X cutting in and out

it is a thermal relay to start cooling fan common fault they go all the time

part no
3872079029

Dave

[electrofix]

Re: AEG lavamat turbo (L 14710-VIT) washer/dryer will not wa

the two are related
earth fault on dryer elements cause this fault

disconnect the dryer element and try a wash

Dave

[electrofix]

Re: Bra Wire Safety Check

you could of course offer to show selected customers how much more support they can expect from a new garment

😆

Dave

[electrofix]

Re: HAUS WM-1050W Control board?

if timer says motor overheats then there has to be a way of detecting it.
there is either a stat in the motor winding that is tripping, wiring to the motor that is going open circuit or the printed circuit board.
Does machine turn motor both ways ? if not look for fault reverse relay on board. look at all relays solder joints with a manifying glass you may not be able to see damage with the naked eye

dont know this machine so thats all i can suggest

Dave

[electrofix]

Re: Mid-life crisis?

iadom wrote:

The examiner used to stand on the street and you rode around the block as he ran from corner to corner keeping an eye on you. 😀

Jim.

agree with that. The examiner on my bike test walked with a limp so would not have been able to keep up with a push bike. My emergency stop was when he stepped out into the road in front of me. I was speeding and breaking traffic rules when he could not see me 😆

Dave

[electrofix]

Re: hotpoint timer

remove motor from rear
remove circlip from top rod then slide out both rods
unclip switch section
gently prise off front switch section one of the contacts will stay attached to main body
if contact has melted housing and moved upwards do not remove or try to reposition
clean contacts and the one that has burnt, remove the switching strip and bend it slightly to help it make connection with both contacts ( because its melted the case and moved contact)
cafefully bring the units back together you will have to carefully push the contact that remained on the main body under the switching bar
put both timer halves back together and put rods in
test with a multimeter to see if you continuity. be aware one of the contacts wont work with timer knob in off position. waggle timer knob shaft to make sure contact wont disconnect. if it does strip down again and bend contact a bit more and repeat
when reinstalling timer clean all brass connection and use 4 new spade connectors and discard green block

hope this may help

Dave

[electrofix]

Re: Proline PLC55FFS

connect or Qualtex dont list

dont know if this is anything in disguise but its a comet own brand and they will supply spares

Dave

[electrofix]

Re: hotpoint timer

you can normally fix them by taking apart done loads never scrapped one for that
or what i should say is cant remember scrapping one as these are old machines now

Dave

[electrofix]

Re: HOOVER A3344 DOOR TRIM

old part number 674108

new part number 09003757

qualtex do not say obsolete but is special
connect list as out of stock

rang qual does not appear on hoovers price list they are checking

poss alternative 09034554
this i think is the same but white cant confirm
qualtex denton are showing in stock

Dave

[electrofix]

Re: hotpoint timer

as far as i know yes but its such a rare event these timers fail what wrong with it ?

Dave

[electrofix]

Re: Samsung Fridge Freezer

if you contact R600a (see moderator list above) he seems to have a lot of experience with this make

Dave

[Author]

Posts