Forum Replies Created
-
Posts
-
Re: Miele shock absorbers. Can they just go soft?
that part number comes up as £15.50
searched europart for your model and this part number is not listed but it may well fit
you could also look at
http://www.nettoparts.co.uk/shop/shock- … 4889p.html
this lists your modelhave used them before and they are very quick
Dave
Re: Indesit Washer dryer WIDL146
Martin wrote:
In fact I have to applaud the efforts of Indesit in making this tin box run for 3 yrs……and perhaps qualifies for a Guinness Book of Records surely? 😈😆
Dave
Re: Qualtex/jet freestanding cooker
first trying not to state the obvious what have qualtex said about it ?
second what parts do you need ?
third any model numbers etc would prob be a beko or the like in disguise
Dave
Re: help with wash machine model number
this will be a model number only available in holland so searching this number will only give you dutch sites
you need to talk to zanussi in holland for an english translation as zanussi uk will not know the model
Dave
Re: Indesit Washer dryer WIDL146
it is my understanding that the retailer is liable under EU law as your contract is with them and not indesit
see the following
http://webarchive.nationalarchives.gov. … 38311.html
Dave
Re: Lamona Washing Machine got mind of it’s own!
dont know which machine you have got but searching lamona auto on google brought up
this machine is a candy in disguise and the selector behind the proramme knob will be your problem. If the contacts get dirty it selects wrong programme. had one the other day that was set on a 40 wash and did a 90
just buy a new selector and fit it thay are not too expensiveDave
Re: Indesit Washer dryer WIDL146
What a load of tosh !!
how can the customer acertain what a load will do during the cycle?
if this was such a bad problem why have indesit not done a software update to correct it. After all it is the software that decides whether to allow a load to spin or not
This is obviously bad design which the engineer tried blame on the customerDave
Re: Hotpoint aqxxl129
if you send the board to emw send both boards and they can test as a pair
Dave
Re: Bosch Exxcel 1400S Filter Cap Leaking
take out plug!!!
remove kickstrip ( 1 torx screw and slide to the right )
take of base plate (if yours has on ) 4 screws
undo screw holding pump to fram at front 1 screw
with machine tilted up drop pump down being carefull to remove wire
use plier to remove larg hose going into pump beware there may be some water in this so you will need some old towels etc
look into pump wher you have just removed hose and remove debris jamming filter
clean out and re-assemble
hope this helpsDave
Re: AWCT10L circuit diagrams
in that case you need to disconnect everthing and buzz the wiring through with a meter
you need to follow current flow and you have not got many components its only going to be valves, door lock or pump and my money would be on the door lock firstDave
Re: whirlpool tumble dryer Awz7303
both stats should buzz when on buzzer setting
element should read under 100 ohm on resistance scale
if element is reading infinity its dud
if stats read infinity they are dudDave
Re: whirlpool tumble dryer Awz7303
stats should read short circuit
element will have a resistance below 100 ohms
stats available here
Re: siwamat 5100 does not spin out
from the description you have water left in the machine
its either blocked socks etc or the pumps gone. if the pump has gone it will not pump out at all. if its blocked it will pump out but very slowly.
if its got a filter check it
Dave
Re: Belling XOU 594
connect show it but its their own part numbers
5031682211731
cant find on qualtex
Dave
Re: AWCT10L circuit diagrams
have you looked at Amica tech site. you will need you username and password to access
https://serwis.amicainternational.com/
Dave
