[electrofix]

Re: de detrich dishwasher

just assumed the hinges had bent this has bent so much door wont close

if it is the cab will it be scrap or is it fixable ?

[electrofix]

Re: hotpoint tdc32

not sure but i seem to recall that if the stats fail it brings on some of the warning lights if you have not checked them its worth doing so

Dave

[electrofix]

Re: Zanussi WD1250 PCB

you should have them let me know how you get on

Dave

[electrofix]

Re: Zanussi DA6152 Dishwasher

no problem robbie pm me an email address

it is worth buying lux disk it has all info and fault codes and more info than you need for under £30

[electrofix]

Re: Zanussi WD1250 PCB

yes they do through the control panel have got docs if you need them will take you ten minutes when you know how

am here till 1 pm if you pm me an email ill attach them to you

ps it is worth buying lux dvd at under £30 it has more info than you caould ever need and all current part prices

Dave

[electrofix]

Re: Sale of Dangerous Parts to the Public.

i can remember having to go on a training course at Dill and sons in leeds to be able to get a number to allow me to buy Zanussi microwave spares
and sharp at the time would only supply to agents who had a list of spares they could supply to the public. if the spare was not on list the could lose their agancy if they sold it

i would be in favour of a legal ban no gas work but only when corgis monopoly is broken. i am not registered but the costs seem very high for all concerned which puts up the end cost making it more likely that a consumer will do their own repairs to save money i for one do my own boiler repairs and gas piping in my own house but have enough knowledge for there not to be a problem

i did enquire about a corgi course and was told i would have to get a plumbing qualification first which i am sur must be wrong

Dave

[electrofix]

Re: Hotpoint wma drums

dont have a problem getting bearing ring out have a 97{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} success rate so far

split a new bearing into components and rebuild into rear half using 5 or 6 balls and centre of race . place balls equally around and holding in place invert tub and belt 7 bells out of race till it comes out

if you clean around ring and oil it it normally slips out without too much trouble

Dave

[electrofix]

Re: software required

software to reprogramme chips should not be a problem the problem is the operating software to put on the chips

have got a programmer i bought years ago to programme satellite cards and it can programme most pic chips

http://www.adteknik.se/english/mp35ser.htm

it will read chips as well but would have to find out if that chip can be read it may be read protected in which case we need a helpful engineer

Dave

[electrofix]

Re: diplomat ADP8242

ok will go back and try asssume you mean if it is o/c it will stop machine

thanks

Dave

[electrofix]

Re: dasa

left dasa some years ago not because i did not agree with the ideals of the organization purely because of cost could not justify the cost in a rapidly shrinking market when they charged by the engineer.needed to eat occasionally

[electrofix]

Re: Indesits Partfinder

not sure if this would work but if you do not let it expire but reset the date before it does see what happens

ie put it back a week each day to see if prog reacts

Dave

[electrofix]

Re: Indesits Partfinder

i am still running an old copy with no probs but this was before partfind and fastrak discs were combined

have date set in 2001 and the disks cant tell. not had a later disk to experiment with but may risk £50 in near future

Dave

[electrofix]

Re: TDS disc

i use a cd rom emulator this allows me to load and image of the complete cd on the hard drive and the computer treats it as a cd rom

i now have 3 ghost cd roms on my system and the system will take more if i can find more disks to run. they can be dvd or cd roms

this also means i can run one cd on several systems

hope this helps

dave

[electrofix]

Re: indesit dishwasher

model no is IDL500uk2 if this helps
412111315
373198410100
machine was given to customer after her freinds mnachine was exchanged and they forgot to pick up old one. from what she is saying it sound although they have chyanged all sorts to cur fault to no avail. if it is somthing simple they have missed its worth doing. i have had the machine heating then after i left house fault codes reoccurred if it is the board is it worth it or are they junk?

Dave

[electrofix]

Re: fuse creda

have had a fuse on a timer that is soldered into the board but if you remove it and take off the caps the value s printed on it cant remember value

older hotpoint machines used a 7a fuse if you replaced around this value you would be ok

Dave

[Author]

Posts