Forum Replies Created
-
Posts
-
Re: Where’s everybody gone?
i think theres a few on here who need to remember what it feels like when you get an awkward customer who stands over you all teh time. is already irritated their machines bearings have gone. not your fault, your only there to fix it. and gradually gets more and more hacked off as you spend 4 hours replacing them because half the bearing casing its wedged in the tub.
thats kinda how i would imagine ken must feel about the site.
repairs in some areas may be down, but ask yourself why is that?
round here repairs are all thats going on and we have a shop too. if it wasnt for the repairs we’d be sunk. i dont beleive in the poorer areas people are giving up on repairs, it defies logic if your on a shoestring.
people on here have been slating y/pages and thomson and bt etc but think about it, if you need a repair where as a client would you look? theres still a lot of traditional people who havent got internet…
Re: Bosch Oven Problem
it also depends on the wear and tear to the fan motor, occasionally all you need to do is clean them up as its only a build up of grease and food residue which causes them to become intermittent and stick/slow, but you kinda need to have seen enough good ones and enough bad ones to know when thats a possibility. hth
Re: WD420 Coin hoard!
spimps wrote:Amazing one didn’t come through the drum or crack it.
The inner drum wll be in a sorry state.:)maybe its the merloni-authorised way of removing the cheesegrater effect of the outside of the inner drum! has it stopped her getting little holes in her clothes?
Re: Stock availability from certain supplier.
you could use pjh or swift for built in if you want reliable always in stock service. both are nationwide and seem to be pretty good with stock levels of built in. not only will they allow you a smidge of margin, but far better to support them than the netguys and chainstores the rest of us indie retailer/repair guys are in competition with!
Re: How do YOU pronounce it?
ok on another note, this was of a full raging discussion for the whole weekend at doningtons download festival last weekend…
JAYGERMYSTER OR
YAYGERMEESTA… or other…
Re: model number
ff72p do you ? thats the no of a s/h one we have in the shop with an oval display….
Re: Hotpoint LFT114 Dishwaher
the waste non-return flap on the pump housing hasnt got pushed in has it??
Re: WD420 Coin hoard!
i think her unreliable hotpoint has just paid half of her repair… the stupid *&!{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}@
Re: Bosch Oven Problem
you say the fan is not running, how have you come to this conclusion? also, a pattern fan for boschs is widely available at about £50 cheaper than an original part. i would argue without paying for labour, a pattern fan, and pattern or genuine element for this is a better buy than shelling out £400 for an equivalent bosch/neff oven… unless its absolutely ghastly and filthy inside 😉
Re: candy cds120 semi int d/w 2006??? no worky
managed to find and unscrew, nothing holding it down, it clicks ok and shows a break in current when depressed too. so assuming its ok, so looks like p/s ???
Re: candy cds120 semi int d/w 2006??? no worky
cheers phil, ill look tomorrow before processing order, thats poss whats happened to this as it worked till 3/4 way thru here, but it might be that its just a bit too gunked.
Re: hoover hnc170-80 motor parts modifications ???
good old connect stuff up again ! cheers bob thATS PERFECT part, and loopy, spot on with no1 although thats now superceded with bobs code. its annoying i ordered the white jockeys thru qtx cos if it was thru connect i could get them returned 🙁 oh well at least i can get it fixed now
Re: candy cds120 semi int d/w 2006??? no worky
3 flashes so im assuming its one of the pressure switches are done in by the clogged u bend (it was also on a spike) as its on the test rig, and tehres not a blockage to be found 😀 do you have prt nos for the p/s ? connect and qualtex dont list any for this model 🙁
