Forum Replies Created
-
Posts
-
Re: Zanussi ZWF1220w Will not pump out when put through a pr
Sorry
Forgot to mention to check to heater insulation as well
Geoff
Re: Zanussi ZWF1220w Will not pump out when put through a pr
Bernie
Can I ask if the end light is lit to show that the machine has completed the cycle or is the start light flashing.
I ask this as I have had several where they abort the programme during the cycle with the start light flashing. User believes that the cycle has completed but clothes are still wet or even water in the drum.
When you do spin it works okI have found either the motor toc or the module causing this.
Geoff
Re: Miele KTN4352 Alarm
Hi
This unit doesnt have a digital display. It has a bank on 5 vertical leds for fridge and one for freezer. These do not appear to give any type of codes??
Will this fridge freezer have some sort of system for fault indication using these lights?Geoff
Re: Zanussi ZWF1621
Just to bring this one up to date.
Changed motor over but it the fault returned once the machince started to fill. this was worse than before.
This fault was located to the heater being down to earth. Changed over heater and awayt it went 😆 well not for long 😥 back to its old tricks but it seem to happen at different times during each cycle. machine may be on hour and stops. start it again 5 mins stops. start it again 1min stop. start it again 15 mins stop 👿
Luck was shining down on me Friday as I went to a call for the same model of machine but had to write it off as there was a hole through the bottem of the welded tub. The lady had no problems with we taking old machine away after installing new machine.
Back at home module out of the leaking one and into may problem machine and away it went 😆
and it is still going 3 cycles later 😀What have I learnt?
If it stops early in the programme it could be heater or module but if it stops later ie rinses and spins it could be the toc in motor.
I will carry the board to use as a test moduleGeoff
Re: Bosch washer error 21
Hi
If you go into search and type in AND BOSCH F21 it will bring up lots of information for you.
In technical trade forum just down from top you will find fault code sticky which lists fault codes for all makes of machinesGeoff
Re: DW60BI
Just to update.
part number is 012g4050243 and is possible haier/PAB product. In connect it comes up as a Baumatic part
will try and see
Geoff
Re: Servis M9503W1
Just to update this one
I had live through elemenets and cut outs and the cable lead to a pcb behind facia panel. The orange coloured relay seem to work ok but in fact was not completing the circuit. replaced replay on board and all is weel
Part number for relay 6804047 from R.S.
Just to recap Fan, condensor valve motor etc all worked when on tumble dry but there was no heat.
Geoff
Re: Neff S4262wo gb09
Hi Clive
Thank you for the help. I will check the pipe to make sure. float is ok
Again thanks you
Geoff
Re: Old New World cooker CKG32508
Hi
many thanks for coming back to me and sorry for the delay in reply as been on holiday
Geoff
Re: Zanussi ZWF1621
Hi
Have been with machine when gone faulty and no problems have shown when all parts are checked via megger.
I suspect motor which just before I went on holiday 2 weeks ago I managed to secure a new one from flea bay.
will try that this week and let you know.
Geoff
Re: Old Crouzet timer motor?
Jim
I have not got one but the part numbers quoted are in stock with Qualtex
Geoff
Re: Part no for Indesit WIXL133 module
Hi
On pathfinder
module (lower) C00263581 but will also need smart card to programme C00267986 and smart card reader.
display module is c00254544
Could send old module back to EMW who repair and send back to you ready programmed.
Geoff
