helo_75

Forum Replies Created

Viewing 15 posts - 136 through 150 (of 4,174 total)
1 2 3 … 9 10 11 … 277 278 279
  • Author
    Posts
  • May 31, 2011 at 3:32 pm in reply to: wd420 hotpoint #352398
    helo_75
    Participant

    Re: wd420 hotpoint

    c00199348

    May 30, 2011 at 10:40 am in reply to: hoover optima oph714d #306617
    helo_75
    Participant

    Re: hoover optima oph714d

    see previous post made by me!

    May 26, 2011 at 8:51 pm in reply to: comet #351651
    helo_75
    Participant

    Re: comet

    interesting how they only now talk about closing service centers? this was decided sometime ago.. the aim of the closures was to inject money onto the bottom line… will service go? bought out guarantees and own warranty repair work would suggest not, but it isnt madly busy, we’re just waitin for the cutbacks

    as for comet as a whole, no idea, who would buy it? and a reported £640 million cost to shut it down, the future is as uncertain as ever

    May 25, 2011 at 8:39 pm in reply to: hoover vhc391-80 #352150
    helo_75
    Participant

    Re: hoover vhc391-80

    just take off and clean the two valves , one on the tank, the other on the back, itll be full of fluff

    May 23, 2011 at 7:57 am in reply to: Hoover HNWL 6136-80 N. 310008970687965 #351890
    helo_75
    Participant

    Re: Hoover HNWL 6136-80 N. 310008970687965

    ok, u carry on there… just cos it heats up, doesnt mean it isnt faulty… no wonder i gave over posting

    May 23, 2011 at 1:44 am in reply to: Indesit wi101 problem #351948
    helo_75
    Participant

    Re: Indesit wi101 problem

    f2 – faulty motor

    if ur lucky, could just be brushes

    May 23, 2011 at 1:35 am in reply to: hoover optima oph714d #306614
    helo_75
    Participant

    Re: hoover optima oph714d

    save youself some time and just put a new heater in, the e03 can be caused by the heater, and e16 is a faulty heater anyway

    overanalyzing will cost you dear!

    May 23, 2011 at 1:27 am in reply to: Aqualtis AQ9L 291(UK)V #351920
    helo_75
    Participant

    Re: Aqualtis AQ9L 291(UK)V

    gotta ask why you need a pressure switch? theyre analogic on those,. and rarely fail

    May 23, 2011 at 1:19 am in reply to: Hoover HNWL 6136-80 N. 310008970687965 #351888
    helo_75
    Participant

    Re: Hoover HNWL 6136-80 N. 310008970687965

    the time out on drain fault is a faulty heater…. the other fault is a fulty selector

    April 27, 2011 at 8:43 pm in reply to: Hotpoint FF187 #350098
    helo_75
    Participant

    Re: Hotpoint FF187

    nah, theres a kit for that, u got a serial number?

    April 16, 2011 at 6:26 pm in reply to: Indesit IWDC6125 Runs dryer after wash cycle #349374
    helo_75
    Participant

    Re: Indesit IWDC6125 Runs dryer after wash cycle

    or the knobs just broken?

    March 18, 2011 at 9:40 pm in reply to: wdl520 and wdl540 #299442
    helo_75
    Participant

    Re: wdl520 and wdl540

    i posted on this very issue not so long ago

    theyre going down for laughs, and should always be the first point of call on these rank machines

    March 14, 2011 at 4:33 pm in reply to: Blomberg 1301ABB #346987
    helo_75
    Participant

    Re: Blomberg 1301ABB

    its more likely a timer fault then

    March 13, 2011 at 1:44 pm in reply to: Hotpoint TVM560 noisy on operation #347028
    helo_75
    Participant

    Re: Hotpoint TVM560 noisy on operation

    its probably worth taking the small access panel of on the back.. its in the middle, held on with 2 screws… if the shaft or bearing is broken, u have serious issues

    March 13, 2011 at 12:24 am in reply to: Creda Europa S077EE oven #346683
    helo_75
    Participant

    Re: Creda Europa S077EE oven

    u have email….

  • Author
    Posts
Viewing 15 posts - 136 through 150 (of 4,174 total)
1 2 3 … 9 10 11 … 277 278 279