Forum Replies Created
-
Posts
-
Re: Hotpoint LFT114UK F02 error
No its part of the water inlet chamber mounted inside the left hand side panel ,looking from front.
You have to do a resistance test on a fill valve, they will fail a simple continuity test with a bog standard multimeter due to high resistance. 😉
Re: Hotpoint LFT114UK F02 error
You should never, under any circumstances ‘adjust’ the pressure switch. Not sure what you heard after you did.
AFAIK this dishwasher doesn’t show numerical codes but flashes the lights to give the error code.
Both F02 and F06 are related and it is possible there was nothing wrong with the fill valve in the first place.
It is more likely to be a faulty fill turbine, you may get lucky and be able to put the pressure switch back to its correct setting or you may have also damaged that.
Re: Wma42
Board is still available, C00202268. In stock at Masterpart. 😆
£65 + vat
Or even HERE for a little more. 😉Re: tcm580g s/n004296022 cc95686860000
Your in luck Cliff, check your inbox.
Not sure if your email has been hacked though, I get quite a few very dodgy bogus messages from C.Noble. 🙁
Jim.
Re: ‘STORE’ doesn’t work on iPad.
More likely to be a software/browser problem, all the store links load in a flash when accessed from the home page but not the forum pages.
If I hold the Store tab for a couple of seconds when on forum pages and then select Open from the options box that appears it will then open the Store but the drop down list of categories that appears if I tap Store in the forum pages will not load anything?
Update.
Just tried using Google Chrome on my iPad and it works so it must be conflict between the forum software and Safari.
Re: Hotpoint EW92
Front left and front?
Better if you give us the position of the knobs from left to right Tim as the diagram doesn’t tell you which reg is for which ring.
If it helps the single hob elements use reg C00240957 and the dual hob ring reg is C00199656.
Jim.
Re: Hotpoint Fridge/Freezer Module PCB control units.
TESTS TO BE CARRIED OUT AFTER REPLACING THE CONTROL MODULE
Connect the appliance to a power supply
Buttons must be pressed one at a time and in the following order to eliminate the individual
LEDs.
All LEDs are switched on
1. Press and release the Holiday button – Switches the Holiday LED off.
2. Press and release the Fast Freeze button – Switches the High Temperature Alarm and the Fast
Freeze LEDs off – see Note below.
3. Press and release the Food Defrost Alert button – Switches the Food Defrost Alert LED off.
NOTE: – The High Temperature LED will not be switched off if the evaporator is not colder than
-15°C.
Passed test reaction
If all buttons pressed are sensed (LEDs OFF), the appliance returns to normal operation.
Where an LED failed to be turned OFF further diagnosis will be required with that function or
functions.Re: Hotpoint dsc90p
Then the parts diagram above is correct for your oven.
It looks like it only has a regulator for the grill, the four left hand units are ‘ 6 way switches’ ?
Re: Hotpoint dsc90p
Model number appears to be incorrect so can’t tell you???
I can only see DSC50 and DSC60 models and they don’t appear to have regulators for some of the hotplates????????
Re: L16820 AEG washr dryer diagnostics program
Likeliest error codes are these.
http://www.ukwhitegoods.co.uk/help/faul … rror-codesRe: Hotpoint Aqualtis AQM8F 49U washer/dryer
In theory yes, but I haven’t heard of any success stories trying to do so. 🙁
Re: Flying tonight. 🙂
If anything this is even more impressive. Just bought a new iPad Air. This reading over wifi a few minutes ago.
The best I can get on my old iPad2 is around 44GB so there are some serious internal improvements on the iPad Air 2. 8)
Re: Hotpoint Aqualtis AQM8F 49U washer/dryer
THESE are the same error codes as used on your machine.
It could be the relay on the main pcb faulty but can also be bad connections to the dryer ntc.
