iadom

Forum Replies Created

Viewing 15 posts - 4,066 through 4,080 (of 25,656 total)
  • Author
    Posts
  • in reply to: Why can’t liquids/tablets and gels contain bleach? #417729
    iadom
    Moderator

    Re: Why can’t liquids/tablets and gels contain bleach?

    And in bottles of liquid detergent the bleach would separate and sink to the bottom. Now even if you put ‘shake the bottle first’ on the side, could you trust the great British public to actually read the label in the first place. :rolls:

    in reply to: beko wm5120w pausing itself #417260
    iadom
    Moderator

    Re: beko wm5120w pausing itself

    The initial complaint was no spin but I found it sticking in several places when I tried it.

    it is the one and only time I have used a pressure switch on one as well.

    in reply to: Beko wma1512 #417699
    iadom
    Moderator

    Re: Beko wma1512

    Moved to correct forum.

    If you are in the trade then you should apply for trade access ASAP.

    Link HERE

    What if anything did you check on this machine, motor brushes for instance?

    in reply to: beko wm5120w pausing itself #417258
    iadom
    Moderator

    Re: beko wm5120w pausing itself

    Once had a weird CI555WH fault that turned out to be an intermittent pressure switch fault.

    Head scratcher

    in reply to: Hotpoint WML740G #417640
    iadom
    Moderator

    Re: Hotpoint WML740G

    I think UN12102 from Masterpart will fit Sole motors but there are plenty of Sole alternatives that will fit.

    in reply to: Old Hoover Logic thermostat required #417617
    iadom
    Moderator

    Re: Old Hoover Logic thermostat required

    Alledgedly. 😉

    in reply to: indesit idl10suk.c 6440685 not heating #417629
    iadom
    Moderator

    Re: indesit idl10suk.c 6440685 not heating

    Are you using a neon screwdriver to check for live?

    in reply to: Hotpoint WML740G #417638
    iadom
    Moderator

    Re: Hotpoint WML740G

    Need full commercial code to be exact.

    Screwed drum/CC 054703 door seal is C00143605.

    Welded drum/CC 064624 door seal is C00111416.

    Generic SOLE motor brushes will fit as long as you get the correct angled carbons, or carefully file them to the correct profile, but do you mean CESET motor brushes, don’t think I have seen SOLE motors in Hotpoint machines??

    in reply to: ISE, AW23 showing E35? #417604
    iadom
    Moderator

    Re: ISE, AW23 showing E35?

    Why is E35 not listed anywhere though?

    She is going to try it again and take a picture of E35 if it comes up again, will try an ntc if it happens again.

    in reply to: Bosch W/D door seal #417555
    iadom
    Moderator

    Re: Bosch W/D door seal

    Cheers Andy, suspected as much. 🙁

    Jim.

    in reply to: Masterpart website un-usable #393627
    iadom
    Moderator

    Re: Masterpart website un-usable

    Site seems to down ATM. 🙁

    in reply to: All checks out but no heat..!! #417542
    iadom
    Moderator

    Re: All checks out but no heat..!!

    On a lot of Zanussi dryers there is a stat located inside the door surround, right at the very top, inside, just left of centre, a bit of a fiddle but held in by two screws. Lie it on it’s back and you should be able to see it better from there.

    in reply to: Ariston avxxf129 washing machine won’t spin #417527
    iadom
    Moderator

    Re: Ariston avxxf129 washing machine won’t spin

    Just put eight flashes in the washing machine forum search box. Anything that comes up related to Hotpoint, Indesit or Ariston relates to your problem, suffice to say it is generally not good news. 🙁

    in reply to: Ariston avxxf129 washing machine won’t spin #417525
    iadom
    Moderator

    Re: Ariston avxxf129 washing machine won’t spin

    Do a forum search, Enter Indesit and eight flashes, same machine, same error code. :rolls:

    in reply to: Retirement #417382
    iadom
    Moderator

    Re: Retirement

    Hardly unique, the OP professed to doing very much the same. 😉

Viewing 15 posts - 4,066 through 4,080 (of 25,656 total)